Pinpoint Test G : B1B36:12, B1B38:12, B1B40:12, B1B42:12

G1 RETRIEVE THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE PARKING AID MODULE (PAM) SELF-TEST

Using a scan tool, perform the Parking Aid Module (PAM) self-test.

Check the Parking Aid Module (PAM) Diagnostic Trouble Codes (DTCs) from the self-test.

Are multiple rear parking aid sensor Diagnostic Trouble Codes (DTCs) recorded?

Yes

GO to G2

No	For Diagnostic Trouble Codes (DTCs) B1B44:12, B1B46:12, B1B48:12 or B1B50:12, GO to G3 For all other Diagnostic Trouble Codes (DTCs), REFER to the DTC Chart: Parking Aid Module (PAM) .

G2 CHECK THE FRONT BUMPER WIRING HARNESS
- Ignition OFF.
- Inspect the front bumper wiring harness for opens, shorts, grounds, or corrosion.
Is the front bumper wiring harness OK?

Yes GO to G3

No REPAIR or INSTALL a new front bumper wiring harness.

G3 CHECK THE FRONT PARKING AID SENSOR CIRCUITRY FOR A SHORT TO VOLTAGE

Disconnect: suspect parking aid sensor(s).

Disconnect BCM C2280C .

Ignition ON.

For DTC B1B36:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1431-2	Courtesy of FORD MOTOR COMPANY	Ground

For DTC B1B38:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1430-2	Courtesy of FORD MOTOR COMPANY	Ground

For DTC B1B40:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1428-2	Courtesy of FORD MOTOR COMPANY	Ground

For DTC B1B42:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1429-2	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the circuit in question.

GO to G4

G4 CHECK THE REAR PARKING AID SENSOR CIRCUITRY FOR A SHORT TOGETHER

Ignition OFF.

For DTC B1B36:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1431-2	Courtesy of FORD MOTOR COMPANY	C1431-1

For DTC B1B38:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1430-2	Courtesy of FORD MOTOR COMPANY	C1430-1

For DTC B1B40:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1428-2	Courtesy of FORD MOTOR COMPANY	C1428-1

For DTC B1B42:12, measure:

Positive Lead	Measurement / Action	Negative Lead
C1429-2	Courtesy of FORD MOTOR COMPANY	C1429-1

Is the resistance greater than 10, 000 ohms?

Yes	If all the sensor Diagnostic Trouble Codes (DTCs) are set, GO to G5. If one or more (but not all) parking aid sensor(s) recorded Diagnostic Trouble Codes (DTCs), INSTALL a new sensor(s) for the one in question. REFER to: Front Parking Aid Sensor .

No	REPAIR the circuits in question.

G5 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

Ignition OFF.

Disconnect and inspect all BCM connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the BCM connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes

CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a Technical Service Bulletin (TSB) exists for this concern, DISCONTINUE this test and FOLLOW Technical Service Bulletin (TSB) instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to BCM Hardware Testing (Except Hybrid/Energi) .

No	The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.