Pinpoint Test B : Shift Solenoid B (SSB)

WARNING: This page is about a different car, the 2015 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.

B1 RETRIEVE AND RECORD ALL DTCS

Using the diagnostic scan tool, retrieve all DTCs.

Are DTCs P0755, P0758, P0759, P0976 and/or P0977 present?

Yes	For DTCs P0755, P0758 and P0759, GO to B2For DTC P0976, GO to B5For DTC P0977, GO to B7

No	REFER to: Diagnosis By Symptom .

B2 CHECK THE SHIFT SOLENOID B (SSB) CONTROL CIRCUIT FOR AN OPEN

Ignition OFF.

Disconnect Transmission Vehicle Harness C1520A .

Disconnect PCM C1915E .

Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C1520A-9	Courtesy of FORD MOTOR COMPANY	C1915E-45

Is the resistance less than 3 ohms?

Yes

GO to B3

No	REPAIR the circuit.

B3 CHECK THE SHIFT SOLENOID B (SSB) FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
Component side resistance pin 9.	Courtesy of FORD MOTOR COMPANY	Component side resistance pin 5.

Is the resistance between 4.2 and 7.2 ohms?

Yes	INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . Refer to: Transmission Strategy Download .

GO to B4

B4 CHECK SHIFT SOLENOID B (SSB) RESISTANCE

Remove the transmission internal wiring harness frame. Refer to: Transmission Internal Wiring Harness Frame . Inspect for metal shavings on the exposed metal contacts or other components and clean the solenoid and transmission internal wiring harness frame terminals.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Shift Solenoid B (SSB) pin A.	Courtesy of FORD MOTOR COMPANY	Shift Solenoid B (SSB) pin B.

Is the resistance between 4.2 and 7.2 ohms?

Yes	INSTALL a new transmission internal wiring harness frame. Refer to: Transmission Internal Wiring Harness Frame .

No	INSTALL a new Shift Solenoid B (SSB). Refer to: Solenoid .

B5 CHECK THE SHIFT SOLENOID B (SSB) CONTROL CIRCUIT FOR A SHORT TO GROUND

Ignition OFF.

Disconnect Transmission Vehicle Harness C1520A .

Disconnect PCM C1915E .

Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C1520A-9	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to B6

No	REPAIR the circuit.

B6 CHECK SHIFT SOLENOID B (SSB) FOR A SHORT TO GROUND

Remove the transmission internal wiring harness frame. Refer to: Transmission Internal Wiring Harness Frame . Inspect for metal shavings on the exposed metal contacts or other components and clean the solenoid and transmission internal wiring harness frame terminals.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Shift Solenoid B (SSB) pin A.	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance less than 5 ohms?

Yes	INSTALL a new Shift Solenoid B (SSB). Refer to: Solenoid .

No	INSTALL a new transmission internal wiring harness frame. Refer to: Transmission Internal Wiring Harness Frame .

B7 CHECK THE SHIFT SOLENOID B (SSB) CONTROL CIRCUIT FOR A SHORT TO POWER

Ignition OFF.

Disconnect Transmission Vehicle Harness C1520A .

Disconnect PCM C1915E .

Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C1520A-9	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the circuit.

No	INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .