Engine Mount LH: Installation

4x2/4x4 

1. 1.
   
   Install the LH engine mount-to-cylinder block bracket and the bolts.

   Torque: 46 lb.ft (63 Nm)

Courtesy of FORD MOTOR COMPANY

1. 2.
   
   Position the LH engine mount and hand start the 3 new engine mount-to-frame bolts.
   • Do not tighten at this time.

Courtesy of FORD MOTOR COMPANY

4x4 

1. 3.
   
   Using an adjustable stand, raise the front axle carrier into position. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

1. 4.
   
   Install the lower front axle carrier mounting bushing bolt.

   Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

1. 5.
   
   Install the axle shaft housing carrier bushing bolt.

   Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

1. 6.
   
   Install the upper front axle carrier mounting bushing bolt.

   Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

1. 7.
   
   Remove the adjustable stand. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

4x2/4x4 

1. 8.
   
   Tighten the LH engine mount bolts

   Torque: 129 lb.ft (175 Nm)

Courtesy of FORD MOTOR COMPANY

1. 9.
   
   Using the special tool, lower the engine to the installed position. Use Special Service Tool: 303-F070 Support Bar, Engine.

Courtesy of FORD MOTOR COMPANY

1. 10.
   
   Remove Special Service Tool: 303-F070 Support Bar, Engine.

Courtesy of FORD MOTOR COMPANY

1. 11.
   
   Remove the special tool and length of chain. Use Special Service Tool: 303-050 (T70P-6000) Lifting Bracket, Engine.

Courtesy of FORD MOTOR COMPANY

1. 12.
   
   
   NOTE: Only use hand tools when installing the engine mount stud bolts or damage to the engine mount can occur.

   Install the new RH engine mount stud bolts.

   Torque: 22 lb.ft (30 Nm)

Courtesy of FORD MOTOR COMPANY

1. 13.
   
   
   NOTE: Only use hand tools when installing the engine mount nuts or damage to the engine mount can occur.

   Install the new RH engine mount nuts.

   Torque: 111 lb.ft (150 Nm)

Courtesy of FORD MOTOR COMPANY

1. 14.
   
   
   NOTE: Only use hand tools when tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

   Install the new LH engine mount through bolt.

   Torque: 258 lb.ft (350 Nm)

Courtesy of FORD MOTOR COMPANY

4x4 

1. 15.
   
   Install the front drive shaft. Refer to: Front Driveshaft .

4x2/4x4 

1. 16.
   
   
   NOTE: Only use hand tools when installing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

   Tighten the transmission mount-to-crossmember nuts.

   Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

1. 17.
   
   
   • Position the exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe and install the new bolts.
   • Tighten the inner exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

     Torque: 46 lb.ft (63 Nm)

   • Tighten the outer exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

     Torque: 46 lb.ft (63 Nm)

Courtesy of FORD MOTOR COMPANY

1. 18.
   
   If equipped, install the skid plate and bolts.

   Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

1. 19.
   
   If equipped, install the underbody shield and fasteners.

   Torque: 71 lb.in (8 Nm)

Courtesy of FORD MOTOR COMPANY

1. 20.
   
   If equipped, install the underbody shield and fasteners.

   Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

1. 21.
   
   Install the radiator top shield and the fasteners.

Courtesy of FORD MOTOR COMPANY

1. 22.
   
   
   NOTE: It is not necessary to separate the air cleaner outlet pipe and the air cleaner, the 2 components can be installed as an assembly.

   Install the following items:

   1. Refer to: Air Cleaner .
   2. Refer to: Air Cleaner Outlet Pipe .

1. 23.
   
   
   NOTE: LH shown, RH similar.

   1. 1.
      
      Position the hood shock and attach.

   1. 2.
      
      Install the clip.

Courtesy of FORD MOTOR COMPANY

1. 24.
   
   Position the hood and install the nuts.

   Torque: 18 lb.ft (25 Nm)

Courtesy of FORD MOTOR COMPANY

1. 25.
   
   Start engine and check exhaust system for leaks.