Engine Mount RH: Installation

4x2/4x4 

• 1.
  
  
  NOTE: If a new engine mount is installed, remove the 2 studs prior to positioning the assembly in the vehicle.

  Install the engine mount and the new bolts.

  Torque: 57 lb.ft (77 Nm)

Courtesy of FORD MOTOR COMPANY

• 2.
  
  

  • 1.
    
    Using the adjustable stand, lower the engine to the installed position. Use the General Equipment: Vehicle/Axle Stands

  • 2.
    
    Remove the stand.

Courtesy of FORD MOTOR COMPANY

• 3.
  
  
  NOTE: Only use hand tools when installing the engine mount studs or damage to the engine mount can occur.

  Install the engine mount studs.

  Torque: 22 lb.ft (30 Nm)

Courtesy of FORD MOTOR COMPANY

• 4.
  
  
  NOTE: Only use hand tools when installing the engine mount nuts or damage to the engine mount can occur.

  Install the new engine mount nuts.

  Torque: 111 lb.ft (150 Nm)

Courtesy of FORD MOTOR COMPANY

• 5.
  
  
  NOTE: Only use hand tools when tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

  Install the new LH engine mount through bolt.

  Torque: 258 lb.ft (350 Nm)

Courtesy of FORD MOTOR COMPANY

4x2 

• 6.
  
  Position the stabilizer bar and install the new nuts.

  Torque: 41 lb.ft (55 Nm)

Courtesy of FORD MOTOR COMPANY

4x4 

• 7.
  
  Install the front drive shaft. Refer to: Front Driveshaft .

4x2/4x4 

• 8.
  
  
  NOTE: Only use hand tools when installing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

  Tighten the transmission mount-to-crossmember nuts.

  Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

• 9.
  
  
  • Position the exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe and install the new bolts.
  • Tighten the inner exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

    Torque: 46 lb.ft (63 Nm)

  • Tighten the outer exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

    Torque: 46 lb.ft (63 Nm)

Courtesy of FORD MOTOR COMPANY

• 10.
  
  Position the A/C compressor and install the bolts.

  Torque: 18 lb.ft (25 Nm)

Courtesy of FORD MOTOR COMPANY

• 11.
  
  Install the following items:
  1. RH fender splash shield. Refer to: Fender Splash Shield .
  2. RH wheel and tire. Refer to: Wheel and Tire .

• 12.
  
  

  • 1.
    
    Install the pin-type retainer.

  • 2.
    
    Install the ground wire and bolt.

    Torque: 18 lb.ft (25 Nm)

Courtesy of FORD MOTOR COMPANY

• 13.
  
  Install the following items:
  1. Refer to: Accessory Drive Belt .
  2. Refer to: Starter Motor .

• 14.
  
  If equipped, install the skid plate and bolts.

  Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

• 15.
  
  If equipped, install the underbody shield and fasteners.

  Torque: 71 lb.in (8 Nm)

Courtesy of FORD MOTOR COMPANY

• 16.
  
  If equipped, install the underbody shield and fasteners.

  Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

• 17.
  
  Install the following items:
  1. Refer to: Charge Air Cooler (CAC) Outlet Pipe .
  2. RH CAC intake pipe. Refer to: Charge Air Cooler (CAC) Intake Pipe .
  3. Refer to: Air Cleaner Outlet Pipe LH .
  4. Refer to: Air Cleaner Outlet Pipe RH .

• 18.
  
  Connect the battery ground cable. Refer to: Battery Disconnect and Connect .

• 19.
  
  Check the exhaust system for leaks.