Engine Mount LH: Installation

WARNING: This page is about a different variant/trim than selected.

4x2/4x4

1.

Install the engine mount-to-cylinder block bracket and the bolts.
Torque: 57 lb.ft (77 Nm)

Courtesy of FORD MOTOR COMPANY

2.

If removed, install a new engine mount-to-frame nut plate.

Courtesy of FORD MOTOR COMPANY

3.
- 1.
  
  Position the LH engine mount into the bracket opening.
- 2.
  
  Using a twisting motion install the mount.
- 3.
  
  Hand start the new engine mount-to-frame bolts. Do not tighten at this time.

Courtesy of FORD MOTOR COMPANY

4.

Using the adjustable stand, lower the engine to the installed position. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

5.

Install the new LH engine mount through bolt.
- Do not tighten at this time.

Courtesy of FORD MOTOR COMPANY

6.

NOTE: Only use hand tools when installing the engine mount studs or damage to the engine mount can occur.

Install the engine mount studs.

Torque: 22 lb.ft (30 Nm)

Courtesy of FORD MOTOR COMPANY

7.

NOTE: Only use hand tools when installing the engine mount nuts or damage to the engine mount can occur.

Install the new engine mount nuts.

Torque: 111 lb.ft (150 Nm)

Courtesy of FORD MOTOR COMPANY

8.

Remove the stand. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

9.

NOTE: Only use hand tools when removing or installing the engine mount-to-frame bolts or damage to the engine mount-to-frame nut plate can occur.

Tighten the LH engine mount bolts

Torque: 129 lb.ft (175 Nm)

Courtesy of FORD MOTOR COMPANY

10.

NOTE: Only use hand tools when tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

Tighten the LH engine mount through bolt.

Torque: 258 lb.ft (350 Nm)

Courtesy of FORD MOTOR COMPANY

4x2

11.

Position the stabilizer bar and install the new nuts.
Torque: 41 lb.ft (55 Nm)

Courtesy of FORD MOTOR COMPANY

4x4

12.

Using an adjustable stand, raise the front axle carrier into position. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

13.

Install the lower front axle carrier mounting bushing bolt.
Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

14.

Install the axle shaft housing carrier bushing bolt.
Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

15.

Install the upper front axle carrier mounting bushing bolt.
Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

16.

Remove the stand. Use the General Equipment: Vehicle/Axle Stands

Courtesy of FORD MOTOR COMPANY

17.

Install the front drive shaft. Refer to: Front Driveshaft .

4x2/4x4

18.

NOTE: Only use hand tools when installing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

Tighten the transmission mount-to-crossmember nuts.

Torque: 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

19.
- Position the exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe and install the new bolts.
- Tighten the inner exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.
  Torque: 46 lb.ft (63 Nm)
- Tighten the outer exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.
  Torque: 46 lb.ft (63 Nm)

Courtesy of FORD MOTOR COMPANY

20.

If equipped, install the skid plate and bolts.
Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

21.

If equipped, install the underbody shield and fasteners.
Torque: 71 lb.in (8 Nm)

Courtesy of FORD MOTOR COMPANY

22.

If equipped, install the underbody shield and fasteners.
Torque: 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

23.

Install the following items:
1. Refer to: Charge Air Cooler (CAC) Outlet Pipe .
2. LH CAC intake pipe. Refer to: Charge Air Cooler (CAC) Intake Pipe .
3. Refer to: Air Cleaner Outlet Pipe LH .
4. Refer to: Air Cleaner .

24.

Connect the battery ground cable. Refer to: Battery Disconnect and Connect .

25.

Check the exhaust system for leaks.