LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2016 >> Edge SE, AWD >> Repair and Diagnosis (Single Page) >> Electrical >> Gauges >> Information Center - Instrumentation, Message Center And Warning Chimes >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test BO : U0131:00 >> Pinpoint Test BO : U0131:00

Pinpoint Test BO : U0131:00

  1. BO1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.
    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  BO2
    No  CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. BO2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform the network test.

    Does the BCM pass the network test? 

    Yes  GO to  BO3
    No  REFER to: Communications Network .

  3. BO3 PERFORM THE PSCM (POWER STEERING CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the PSCM self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Power Steering .
    No  GO to  BO4

  4. BO4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  GO to  BO5

  5. BO5 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Is DTC U3003:16 or DTC U3003:17 recorded? 

    Yes  REFER to DTC Chart: IPC in this article.
    No  GO to  BO6

  6. BO6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

    NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the Programmable Module Installation (PMI), or the Programmable Module Installation (PMI) may not have been carried out.

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
    • Wait 10 seconds.
    • Repeat the IPC self-test.

    Is DTC U0131:00 still present? 

    Yes  GO to  BO7
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  7. BO7 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0131:87 SET IN OTHER MODULES

    • Using a diagnostic scan tool, clear all Diagnostic Trouble Codes (DTCs).
    • Ignition OFF.
    • Ignition ON.
    • Wait 10 seconds.
    • Using a diagnostic scan tool, perform the continuous memory self-test.
    • Retrieve the Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.

    Is DTC U0131:87 set in the BCM? 

    Yes  GO to  BO8
    No  GO to  BO9

  8. BO8 CHECK FOR CORRECT PSCM (POWER STEERING CONTROL MODULE) OPERATION

    • Ignition OFF.
    • Disconnect and inspect all the PSCM and all related in-line connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect all the PSCM and all related in-line connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, refer to the EPAS symptom chart. Refer to Electronic Power Assist Steering Component Testing
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  9. BO9 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION

    • Ignition OFF.
    • Disconnect and inspect the IPC and all related in-line connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the IPC and all related in-line connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to IPC Hardware Testing .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals