DTC Chart: Instrument Panel Cluster (IPC)
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
DTC Chart - IPC
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | For single sender L-shaped fuel tank, GO to Pinpoint Test C For dual sender saddle-type fuel tank, GO to Pinpoint Test D |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | For single sender L-shaped fuel tank, GO to Pinpoint Test C For dual sender saddle-type fuel tank, GO to Pinpoint Test D |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure | GO to Pinpoint Test D |
| P1346:11 | Fuel Level Sensor "B" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P1346:13 | Fuel Level Sensor "B" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | Refer to IPC Hardware Testing . Diagnose all RCM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS) . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test U |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BK |
| U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to Pinpoint Test BL |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BN |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BO |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BP |
| U0140:81 | Lost Communication With Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test BP |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test BQ |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| U0154:00 | Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test BS |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test BU |
| U0193:00 | Lost Communication With "Digital Audio Control Module A": No Sub Type Information | GO to Pinpoint Test BW |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BV |
| U0199:00 | Lost Communication With "Door Control Module A": No Sub Type Information | GO to Pinpoint Test BX |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BY |
| U0230:00 | Lost Communication With Rear Gate Module - Left: No Sub Type Information | GO to Pinpoint Test BZ |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test CA |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test CA |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test CB |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CC |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test CD |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: No Sub Type Information | GO to Pinpoint Test CE |
| U0260:00 | Lost Communication With Seat Control Switch Module "A": No Sub Type Information | GO to Pinpoint Test CF |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the IPC receives invalid network data for the speedometer, temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data for the speedometer or temperature gauge from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated data for the cruise control or adaptive cruise control from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0402:82 | Invalid Data Received from TCM: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated transmission data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0405:56 | Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data for adaptive cruise control and forward collision warning from the CCM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0415:56 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data for adaptive cruise control and forward collision warning from the CCM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0415:82 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated ABS data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. Refer to: Anti-Lock Brake System (ABS) And Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0420:82 | Invalid Data Received From Power Steering Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive power steering data from the PSCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PSCM and other modules on the network. Refer to: Power Steering . If no Diagnostic Trouble Codes (DTCs) are present in the PSCM, DIAGNOSE the observable symptom. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid network TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. Refer to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0428:82 | Invalid Data Received From Steering Angle Sensor Module Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated steering angle sensor data from the SASM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM and other modules on the network. Refer to: Power Steering . If no Diagnostic Trouble Codes (DTCs) are present in the SASM, DIAGNOSE the observable symptom. |
| U0429:82 | Invalid Data Received From Steering Column Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated turn signal data from the SCCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SCCM and other modules on the network. Refer to: Steering Wheel And Column Electrical Components . If no Diagnostic Trouble Codes (DTCs) are present in the SCCM, DIAGNOSE the observable symptom. |
| U0431:82 | Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated load shed and power child lock data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. Refer to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder ® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. Refer to: Airbag Supplemental Restraint System (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0455:82 | Invalid Data Received From Restraints Occupant Classification System Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated occupant classification data from the RCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. Refer to: Airbag Supplemental Restraint System (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U045A:82 | Invalid Data Received From Parking Assist Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated active park assist data from the PAM (part of the BCM). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. Refer to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U046B:86 | Invalid Data Received From Global Positioning System Module: Signal Invalid | This DTC sets when the IPC receives invalid compass data from the GPSM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the GPSM and other modules on the network. Refer to the appropriate Information and Entertainment System article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the GPSM, DIAGNOSE the observable symptom. |
| U0531:82 | Invalid Data Received From Rear Gate Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated power liftgate data from the RGTM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RGTM and other modules on the network. Refer to: Body Closures . If no Diagnostic Trouble Codes (DTCs) are present in the RGTM, DIAGNOSE the observable symptom. |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data from the SODL. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CA |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data from the SODR. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CA |
| U0557:00 | Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information | This DTC sets when the IPC fails to receive invalid outside air temperature data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. Refer to the appropriate Information and Entertainment System article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:80 | Invalid Data Received From Front Controls Interface Module "A": ISO/SAE Reserved | This DTC sets when the IPC fails to receive invalid outside air temperature data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. Refer to the appropriate Information and Entertainment System article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:81 | Invalid Data Received From Front Controls Interface Module "A": Invalid Serial Data Received | This DTC sets when the IPC fails to receive unknown outside air temperature data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. Refer to the appropriate Information and Entertainment System article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:82 | Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CD |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. Refer to: Module Configuration - System Operation And Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:04 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:42 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:43 | Control Module: Special Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:43 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:44 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:46 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:54 | Control Module: Missing Calibration | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:54 is retrieved again, Refer to IPC Hardware Testing . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test CG |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test CH |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. Refer to: Steering Wheel And Column Electrical Components . |