LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2016 >> Edge SE, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Parking Aid System - Vehicles With Parking Aid Camera >> Diagnosis And Testing >> Parking Aid >> Pinpoint Test(s) >> Pinpoint Test L : The Visual Park Aid Alert Is Inoperative - Vehicles With Front And Rear Parking Aid Camera >> Pinpoint Test L : The Visual Park Aid Alert Is Inoperative - Vehicles With Front And Rear Parking Aid Camera

Pinpoint Test L : The Visual Park Aid Alert Is Inoperative - Vehicles With Front And Rear Parking Aid Camera

  1. L1 VERIFY THE VISUAL PARK AID ALERT IS ENABLED

    • Ignition ON.
    • Verify that the visual park aid alert is enabled in the infotainment system settings menu. Refer to the Owner's Literature.

    Is the visual park aid alert enabled? 

    Yes  GO to  L2
    No  ENABLE the visual park aid alert.

  2. L2 PERFORM A NETWORK TEST

    • Ignition ON.
    • Using a diagnostic scan tool, perform a network test.

    Do all modules pass the network test? 

    Yes  GO to  L3
    No  REFER to: Communications Network .

  3. L3 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE PAM (PARKING ASSIST CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the PAM self-test.

    Are any PAM Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REPAIR all PAM Diagnostic Trouble Codes (DTCs) before continuing this test. REFER to: Parking Aid .
    No  GO to  L4

  4. L4 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPMB (IMAGE PROCESSING MODULE B) SELF-TEST

    • Using a diagnostic scan tool, perform the IPMB self-test.

    Are any IPMB Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to the IPMB DTC chart .
    No  GO to  L5

  5. L5 CHECK FOR CORRECT IPMB (IMAGE PROCESSING MODULE B) OPERATION

    • Ignition OFF.
    • Disconnect and inspect the IPMB connectors and related in-line connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the IPMB connectors and related in-line connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB) .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.

  6. L6 CHECK FOR CORRECT APIM (SYNC MODULE) OPERATION

    • Ignition OFF.
    • Disconnect and inspect the APIM connector and related in-line connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the APIM connector and related in-line connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to APIM Hardware Testing ..
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals