LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2015 >> Transit Connect Titanium >> Repair and Diagnosis (Single Page) >> Electrical >> Gauges >> Instrumentation, Message Center And Warning Chimes >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Ax : U0151:00 >> Pinpoint Test Ax : U0151:00

Pinpoint Test Ax : U0151:00

  1. AX1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.
    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  AX2
    No  The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. AX2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform a network test.

    Does the RCM pass the network test? 

    Yes  GO to  AX3
    No  REFER to: Communications Network

  3. AX3 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE BCM (BODY CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the BCM self-test.

    Is DTC U0151:00 recorded? 

    Yes  REFER to: Body Control Module (BCM)
    No  GO to  AX4

  4. AX4 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Is DTC U3006:16 or DTC U3006:17 recorded? 

    Yes  REFER to DTC Chart: IPC 
    No  GO to  AX5

  5. AX5 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the RCM self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Airbag Supplemental Restraint System (SRS)
    No  GO to  AX6

  6. AX6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
    • Wait 10 seconds.
    • Using a diagnostic scan tool, perform the IPC self-test.

    Is DTC U0151:00 still present? 

    Yes  GO to  AX7
    No  The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  7. AX7 CHECK FOR CORRECT RCM (RESTRAINTS CONTROL MODULE) OPERATION

    • Ignition OFF.
    • Disconnect and inspect all RCM connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the RCM connectors. Make sure they seat and latch correctly.
    • Operate the system and verify the concern is still present

    Is the concern still present? 

    Yes  INSTALL a new RCM. REFER to: Restraints Control Module (RCM) CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U0151:00 is still present, GO to  AX8
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  8. AX8 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION

    • Ignition OFF.
    • Disconnect and inspect the IPC connector.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the IPC connector. Make sure it seats and latches correctly.
    • Operate the system and verify the concern is still present

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to IPC Hardware Testing .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals