DTC Chart: IPC

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices.

DTC CHART - IPC

DTC	Description	Action
P0460:11	Fuel Level Sensor "A" Circuit: Circuit Short To Ground	GO to PINPOINT TEST C
P0460:13	Fuel Level Sensor "A" Circuit: Circuit Open	GO to PINPOINT TEST C
P1534:01	Restraint Deployment Indicator Circuit: General Electrical Failure	INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) . Diagnose all RCM Diagnostic Trouble Codes (DTCs). REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
P1706:00	High Vehicle Speed Observed in Park: No Sub Type Information	GO to PINPOINT TEST O
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to PINPOINT TEST BE
U0104:00	Lost Communication With Cruise Control Module: No Sub Type Information	GO to PINPOINT TEST BF
U0121:00	Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	GO to PINPOINT TEST BG
U0140:00	Lost Communication With Body Control Module: No Sub Type Information	GO to PINPOINT TEST BH
U0146:00	Lost Communication With Gateway "A": No Sub Type Information	GO to PINPOINT TEST BI
U0151:00	Lost Communication With Restraints Control Module: No Sub Type Information	GO to PINPOINT TEST BJ
U0159:00	Lost Communication With Parking Assist Control Module "A": No Sub Type Information	GO to PINPOINT TEST BK
U016A:00	Lost Communication With Global Positioning System Module: No Sub Type Information	GO to PINPOINT TEST BL
U0212:00	Lost Communication With Steering Column Control Module: No Sub Type Information	GO to PINPOINT TEST BM
U0232:00	Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information	GO to PINPOINT TEST BN
U0233:00	Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information	GO to PINPOINT TEST BN
U023A:00	Lost Communication With Image Processing Module A: No Sub Type Information	GO to PINPOINT TEST BO
U0241:00	Lost Communication With Headlamp Control Module "A": No Sub Type Information	GO to PINPOINT TEST BO
U0293:00	Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information	GO to PINPOINT TEST BP
U0401:00	Invalid Data Received from ECM/PCM A: No Sub Type Information	This DTC sets when the IPC receives invalid network data for the speedometer, temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to INTRODUCTION - HYBRID . REFER to: ELECTRONIC ENGINE CONTROLS .
U0401:81	Invalid Data Received from ECM/PCM A: Invalid Serial Data Received	This DTC sets when the IPC receives invalid network data for the speedometer, temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to INTRODUCTION - HYBRID . REFER to: ELECTRONIC ENGINE CONTROLS .
U0401:82	Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated	GO to PINPOINT TEST BE
U0405:56	Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid network data for adaptive cruise control from the CCM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0412:82	Invalid Data Received From Battery Energy Control Module A: Alive/Sequence Counter Incorrect/Not Updated	GO to PINPOINT TEST BQ
U0420:82	Invalid Data Received From Power Steering Control Module: Alive/Sequence Counter Incorrect/Not Updated	GO to PINPOINT TEST BR
U0422:00	Invalid Data Received From Body Control Module: No Sub Type Information	This DTC sets when the IPC receives invalid network TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: BODY CONTROL MODULE (BCM) .
U0424:00	Invalid Data Received From HVAC Control Module: No Sub Type Information	This DTC sets when the IPC receives invalid network data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to: ELECTRONIC ENGINE CONTROLS .
U0424:81	Invalid Data Received From HVAC Control Module: Invalid Serial Data Received	This DTC sets when the IPC receives invalid network data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to: ELECTRONIC ENGINE CONTROLS .
U0424:82	Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated	GO to PINPOINT TEST BS
U0452:81	Invalid Data Received From Restraints Control Module: Invalid Serial Data Received	This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
U046B:86	Invalid Data Received From Global Positioning System Module: Signal Invalid	This DTC sets when the IPC receives invalid network data from the GPSM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the GPSM and other modules on the network. Refer to the appropriate article for the procedure.
U0533:56	Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid network data from the SODL. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0534:56	Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid network data from the SODR. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0594:86	Invalid Data Received From Hybrid/EV Powertrain Control Module: Signal Invalid	This DTC sets when the IPC receives invalid network data from the TCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM and other modules on the network. Refer to INTRODUCTION - HYBRID .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: MODULE CONFIGURATION - 2.0L DURATEC - HYBRID (96KW/130PS) - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U3000:41	Control Module: General Checksum Failure	CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
U3000:42	Control Module: General Memory Failure	CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
U3000:44	Control Module: Data Memory Failure	CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:44 is retrieved again, INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
U3000:46	Control Module: Calibration/Parameter Memory Failure	CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:46 is retrieved again, INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
U3000:54	Control Module: Missing Calibration	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect calibration files. If there have been recent service actions with this module, REFLASH the IPC. If there have been no recent service actions, INSTALL a new IPC. REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST BT
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST BU
U300A:64	Ignition Switch: Signal Plausibility Failure	DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. REFER to: STEERING WHEEL AND COLUMN ELECTRICAL COMPONENTS .