Pinpoint Test F : The FDIM (Front Display Interface Module) Displays An Active Park Assist Fault Message
WARNING: This page is about a different car, the 2015 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
- F1 PERFORM A NETWORK TEST
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Do all modules pass the network test?
Yes GO to F2 No REFER to: Communications Network . - F2 CHECK THE PARKING AID MODULE (PAM) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the Parking Aid Module (PAM) self-test.
Are any Diagnostic Trouble Codes present?
Yes REFER to: Parking Aid . No GO to F3 - F3 CHECK THE PSCM (POWER STEERING CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PSCM self-test.
Are any Diagnostic Trouble Codes present?
Yes REFER to: Power Steering . No GO to F4 - F4 CHECK THE SCCM (STEERING COLUMN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the SCCM self-test.
Are any Diagnostic Trouble Codes present?
Yes REFER to: Steering Wheel and Column Electrical Components . No GO to F5 - F5 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the ABS module self-test.
Are any Diagnostic Trouble Codes present?
Yes REFER to: Anti-Lock Brake System (ABS) and Stability Control . No GO to F6 - F6 CHECK THE PCM (POWERTRAIN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PCM self-test.
Are any Diagnostic Trouble Codes present?
Yes Refer to the appropriate Engine Article for the procedure. No GO to F7 - F7 CHECK THE FCIM (FRONT CONTROLS INTERFACE MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the FCIM self-test.
Are any Diagnostic Trouble Codes present?
Yes Vehicles equipped with Sony sound, REFER to: Information and Entertainment System . Vehicles not equipped with Sony sound, REFER to: Information And Entertainment System . No GO to F8 - F8 CHECK THE BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the BCM self-test.
Are any Diagnostic Trouble Codes present?
Yes REFER to: Body Control Module (BCM) . No GO to F9 - F9 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)
- Ignition OFF.
- Ignition ON.
- Operate the system to determine if the concern is still present.
- Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Are any Diagnostic Trouble Codes present?
Yes REFER to: Communications Network . No GO to F10 - F10 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all BCM connectors.
- Repair:
- corrosion (install new connector or terminals clean module pins)
- damaged or bent pins install new terminals/pins
- pushed-out pins install new pins as necessary
- Reconnect the BCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a Technical Service Bulletin (TSB) exists for this concern, DISCONTINUE this test and FOLLOW Technical Service Bulletin (TSB) instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to BCM Hardware Testing (Except Hybrid/Energi) . No The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.