LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2014 >> Focus ST >> Repair and Diagnosis >> Electrical >> Gauges >> Information Center - Instrumentation, Message Center, And Warning Chimes -- (Except Electric) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> PINPOINT TEST AX: The Compass Display Is Inoperative >> Pinpoint Test Ax: The Compass Display Is Inoperative

Pinpoint Test Ax: The Compass Display Is Inoperative

  1. AX1 CHECK FOR COMPASS ZONE AND CALIBRATION SETTINGS THROUGH THE MESSAGE CENTER 
    • Ignition ON.
    • Enter the vehicle settings in the message center and verify whether the compass zone and calibration setting menu is present.

    Is the compass zone and calibration setting menu present? 

    1. Yes  : GO to  AX4
    2. No  : GO to AX2 
  2. AX2 RETRIEVE THE RECORD DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE GPSM (GLOBAL POSITIONING SYSTEM MODULE) SELF-TEST 
    • Using a scan tool, perform the GPSM  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : For base audio,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD).

      For premium audio,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC).

      For Sony sound,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: Sony AM/FM/CD/SYNC/Touchscreen Display).

    2. No  : GO to AX3 
  3. AX3 RETRIEVE THE RECORD DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE APIM (SYNC MODULE) SELF-TEST 
    • Using a scan tool, perform the IPC  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : For base audio,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD).

      For premium audio,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC).

      For Sony sound,

      REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: Sony AM/FM/CD/SYNC/Touchscreen Display).

    2. No  : GO to AX4 
  4. AX4 RETRIEVE THE RECORD DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST 
    • Using a scan tool, perform the IPC  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : For DTC  U0140:00, GO to PINPOINT TEST AF 

      For all other Diagnostic Trouble Codes (DTCs), REFER to DTC CHART: IPC  in this service information.

    2. No  : For vehicles without the compass zone and calibration setting menu in the message center, INSTALL a new GPSM  .

      REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) (Vehicles With: AM/FM/CD/SYNC).

      REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) (Vehicles With: Sony AM/FM/CD/SYNC/Touchscreen Display).

      For vehicles equipped with the compass zone and calibration setting menu in the message center, GO to AX5 

  5. AX5 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE BCM (BODY CONTROL MODULE) SELF-TEST 
    • Using a scan tool, perform the BCM  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : REFER to: BODY CONTROL MODULE (BCM) .
    2. No  : GO to AX6 
  6. AX6 CHECK THE COMPASS MODULE VOLTAGE SUPPLY 
    • Ignition OFF.
    • Disconnect: Compass Module.
    • Ignition ON.
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C909-1  VOLTAGE Ground

    Is the voltage greater than 11 volts? 

    1. Yes  : GO to AX7 
    2. No  : VERIFY the BCM  fuse 67 (7.5A). If OK, REPAIR the circuit. If not OK, REFER to the OEM WIRING DIAGRAMS -- EXCEPT ELECTRIC to identify the possible causes of the circuit short.
  7. AX7 CHECK THE COMPASS MODULE GROUND CIRCUIT FOR AN OPEN 
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C909-1  VOLTAGE C909-2 

    Is the voltage greater than 11 volts? 

    1. Yes  : GO to AX8 
    2. No  : REPAIR the circuit.
  8. AX8 CHECK THE COMPASS COMMUNICATION BUS FOR A SHORT TO VOLTAGE 
    • Ignition OFF.
    • Disconnect: BCM  C2280H.
    • Ignition ON.
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C909-3  VOLTAGE Ground

    Is any voltage present? 

    1. Yes  : REPAIR the circuit.
    2. No  : GO to AX9 
  9. AX9 CHECK THE COMPASS COMMUNICATION BUS FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C909-3  OHM Ground

    Is the resistance greater than 10, 000 ohms? 

    1. Yes  : GO to AX10 
    2. No  : REPAIR the circuit.
  10. AX10 CHECK THE COMPASS COMMUNICATION BUS FOR AN OPEN 
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C909-3  OHM C2280H-12 

    Is the resistance less than 3 ohms? 

    1. Yes  : INSTALL a new compass module.

      REFER to: COMPASS MODULE .

      SET the compass zone and CALIBRATE the compass. TEST the system for normal operation. If the compass is still inoperative, GO to AX11 

    2. No  : REPAIR the circuit.
  11. AX11 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION 
    • Ignition ON.
    • Disconnect and inspect all BCM  connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the BCM  connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    1. Yes  : CHECK On-Line Automotive Service Information System (OASIS) for any applicable Technical Service Bulletins (TSBs). If a TSB  exists for this concern, DISCONTINUE this test and FOLLOW TSB  instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM  .

      REFER to: BODY CONTROL MODULE (BCM) .

    2. No  : The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals