LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2014 >> Focus Electric >> Repair and Diagnosis >> Electrical >> Gauges >> Information Center - Instrumentation, Message Center, And Warning Chimes -- (Electric) >> Diagnosis and Testing >> Instrumentation, Message Center and Warning Chimes >> Diagnostic Routines >> U0140:00 >> Pinpoint Test AJ: U0140:00

Pinpoint Test AJ: U0140:00

  1. AJ1 VERIFY THE CUSTOMER CONCERN 
    • Ignition ON.
    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    1. Yes  : GO to AJ2 
    2. No  : The system is operating normally at this time. The DTC  may have been set due to high network traffic or an intermittent fault condition. CLEAR the DTC  .
  2. AJ2 CHECK THE COMMUNICATION NETWORK 
    • Using a scan tool, perform the network test.

    Does the BCM pass the network test? 

    1. Yes  : GO to AJ3 
    2. No  : REFER to: COMMUNICATIONS NETWORK .
  3. AJ3 PERFORM THE BODY CONTROL MODULE (BCM) SELF-TEST 
    • Using a scan tool, perform the BCM  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : REFER to: BODY CONTROL MODULE (BCM) .
    2. No  : GO to AJ4 
  4. AJ4 PERFORM THE INSTRUMENT PANEL CLUSTER (IPC) SELF-TEST 
    • Using a scan tool, perform the IPC  self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    1. Yes  : REFER to DTC CHART: IPC .
    2. No  : GO to AJ5 
  5. AJ5 RECHECK THE INSTRUMENT PANEL CLUSTER (IPC) DIAGNOSTIC TROUBLE CODES (DTCS) 
    NOTE: If new modules were installed prior to the DTC  being set, the module configuration may be incorrectly set during the Programmable Module Installation (PMI), or the Programmable Module Installation (PMI) may not have been carried out.
    • Using a scan tool, clear the Diagnostic Trouble Codes (DTCs).
    • Wait 10 seconds.
    • Repeat the IPC  self-test.

    Is DTC U0140:00 still present? 

    1. Yes  : GO to AJ6 
    2. No  : The system is operating correctly at this time. The DTC  may have been set due to high network traffic or an intermittent fault condition. CLEAR the DTC  .
  6. AJ6 CHECK FOR DIAGNOSTIC TROUBLE CODE (DTC) U0140:00 SET IN OTHER MODULES 
    • Using a scan tool, clear all Diagnostic Trouble Codes (DTCs).
    • Ignition OFF.
    • Ignition ON.
    • Wait 10 seconds.
    • Using a scan tool, perform the continuous memory self-test.
    • Retrieve the continuous memory Diagnostic Trouble Codes (DTCs) from all modules.

    Is DTC U0140:00 set in other modules on the network? 

    1. Yes  : REFER to The BCM Does Not Respond To The Diagnostic Scan Tool to DIAGNOSE the CAN circuits.

      REFER to: COMMUNICATIONS NETWORK .

    2. No  : GO to AJ7 
  7. AJ7 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION 
    • Ignition OFF.
    • Disconnect and inspect the IPC  connector.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the IPC  connector. Make sure it seats and latches correctly.
    • Operate the system and verify the concern is still present

    Is the concern still present? 

    1. Yes  : CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB  exists for this concern, DISCONTINUE this test and FOLLOW TSB  instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new IPC  .

      REFER to: INSTRUMENT PANEL CLUSTER (IPC)  .

    2. No  : The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals