LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2014 >> Explorer Sport >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Pinpoint Tests BG - BS >> B140C:11, B140C:12, B140C:13 and B140C:1A >> PINPOINT TEST BJ: B140C:11, B140C:12, B140C:13 and B140C:1A

PINPOINT TEST BJ: B140C:11, B140C:12, B140C:13 and B140C:1A

WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy and cause serious personal injury or death.
WARNING: Never disassemble or tamper with seat belt deployable components, including pretensioners, load limiters and inflators. Never back probe deployable device electrical connectors. Tampering or back probing may cause an accidental deployment and result in personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS  components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs  may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
  1. BJ1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B140C:11, B140C:12, B140C:13 or B140C:1D retrieved on-demand during self-test? 

    1. Yes  : This fault cannot be cleared until it is corrected and the DTC  is no longer retrieved on-demand during self-test.

      For DTC  B140C:11 or B140C:1D, GO to BJ2  .

      For DTC  B140C:12, GO to  BJ4.

      For DTC  B140C:13, GO to  BJ5.

    2. No  : This is an intermittent fault when present as a CMDTC  only. GO to  BJ10.
  2. BJ2 CHECK THE SECOND ROW DRIVER SIDE SEATBELT SENSOR DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED) 
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

      Ignition OFF.

    • Vehicles equipped with a 40 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Remove 5 screws and the seat track inboard inner and outer covers.
      • Detach the cushion cover front and inboard retainers.
      • Lift the cushion cover and foam pad.
    • Vehicles equipped with a 60 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Detach the cushion cover retainers and position the cushion cover aside.
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .
    • DIAGNOSTIC TIP:  When viewing DTCs  with the second row left safety belt buckle switch disconnected, an open circuit fault is normally retrieved.

    Did the on-demand DTC change from B140C:11 or B140C:1D to B140C:13? 

    1. Yes  : GO to  BJ8.
    2. No  : For DTC  B140C:11, GO to BJ3  .

      For DTC  B140C:1D, GO to  BJ9.

  3. BJ3 CHECK THE SECOND ROW LEFT SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO GROUND 

    Is the resistance greater than 10, 000 ohms? 

    1. Yes  : GO to  BJ9.
    2. No  : REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BJ11.

  4. BJ4 CHECK THE SECOND ROW LEFT SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO VOLTAGE 

    Is any voltage present? 

    1. Yes  : REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BJ11.

    2. No  : GO to  BJ9.
  5. BJ5 CHECK THE SECOND ROW DRIVER SIDE SEATBELT SENSOR DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

      Ignition OFF.

    • Vehicles equipped with a 40 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Remove 5 screws and the seat track inboard inner and outer covers.
      • Detach the cushion cover front and inboard retainers.
      • Lift the cushion cover and foam pad.
    • Vehicles equipped with a 60 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Detach the cushion cover retainers and position the cushion cover aside.
    • Connect a fused jumper wire:
      Positive Lead Measurement/Action Negative Lead
      C3646-1  FUSED JUMPER WIRE C3646-2 
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .
    • DIAGNOSTIC TIP:  When viewing DTCs  with the second row left safety belt buckle switch circuits shorted together, a short to ground fault is normally retrieved.

    Did the on-demand DTC change from B140C:13 to B140C:11? 

    1. Yes  : REMOVE the fused jumper wire and GO to  BJ8.
    2. No  : REMOVE the fused jumper wire and GO to BJ6  .
  6. BJ6 CHECK THE SECOND ROW LEFT SAFETY BELT BUCKLE SWITCH CIRCUIT FOR AN OPEN 

    Is the resistance less than 0.5 ohm? 

    1. Yes  : GO to BJ7  .
    2. No  : REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BJ11.

  7. BJ7 CHECK THE SECOND ROW LEFT SAFETY BELT BUCKLE SWITCH GROUND CIRCUIT FOR AN OPEN 
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C3646-2  OHM Ground

    Is the resistance less than 3 ohms? 

    1. Yes  : GO to  BJ9.
    2. No  : REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BJ11.

  8. BJ8 CONFIRM THE SECOND ROW LEFT SAFETY BELT BUCKLE SWITCH FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : INSTALL a new inflatable safety belt buckle. REFER to SAFETY BELT BUCKLE - 2ND ROW, 40 PERCENT SEAT, WITH INFLATABLE SAFETY BELTS or REFER to SAFETY BELT BUCKLE AND INFLATOR - 2ND ROW, 60 PERCENT SEAT . GO to  BJ11.
    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  BJ10.
  9. BJ9 CONFIRM THE RCM FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : CHECK OASIS  for any applicable TSBs  . If a TSB  exists for this concern, discontinue this test and follow TSB  instructions. If no TSBs  address this concern, INSTALL a new RCM  . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  BJ11.
    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to BJ10  .
  10. BJ10 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • Vehicles equipped with a 40 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Remove 5 screws and the seat track inboard inner and outer covers.
      • Detach the cushion cover front and inboard retainers.
      • Lift the cushion cover and foam pad.
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Vehicles equipped with a 60 percent second row left seat:  Disconnect Second Row Left Safety Belt Buckle Switch C3646  .
      • Detach the cushion cover retainers and position the cushion cover aside.
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Inspect RCM CPA  lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
    • Connect all previously disconnected component(s)/connector(s).
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B140C:11, B140C:12, B140C:13 or B140C:1D retrieved on-demand during self-test? 

    1. Yes  : This fault cannot be cleared until it is corrected and the DTC  is no longer retrieved on-demand during self-test.

      For DTC  B140C:11 or B140C:1D, GO to  BJ2.

      For DTC  B140C:12, GO to  BJ4.

      For DTC  B140C:13, GO to  BJ5.

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to BJ11  .
  11. BJ11 CHECK FOR ADDITIONAL SRS DTCs 
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

      Ignition OFF.

    • Reconnect all SRS  components (if previously disconnected).
    • If previously directed to depower the SRS  , repower the SRS  . Do not prove out the SRS at this time  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • Ignition ON.
    • NOTE: When selecting Restraints from the Self-Test menu, DTCs  are retrieved from the RCM  and OCSM  .

      Using a scan tool, perform Restraints  self-test to retrieve DTCs  .

    Are any RCM and/or OCSM DTCs retrieved on-demand during self-test? 

    1. Yes  : Do not clear any DTCs  until all DTCs  have been resolved. REFER to the appropriate DTC CHART for pinpoint test direction.
    2. No  : CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals