LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2014 >> Explorer Sport >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Pinpoint Tests Aa - AQ, Pinpoint Tests BA - Bf >> B1404:11, B1404:12, B1404:13 and B1404:1A >> PINPOINT TEST BF: B1404:11, B1404:12, B1404:13 and B1404:1A

PINPOINT TEST BF: B1404:11, B1404:12, B1404:13 and B1404:1A

WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy and cause serious personal injury or death.
WARNING: Never probe the electrical connectors on airbag, Safety Canopy or side air curtain assemblies. Failure to follow this instruction may result in the accidental deployment of these assemblies, which increases the risk of serious personal injury or death.
WARNING: Never disassemble or tamper with seat belt deployable components, including pretensioners, load limiters and inflators. Never back probe deployable device electrical connectors. Tampering or back probing may cause an accidental deployment and result in personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS  components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs  may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
  1. BF1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B1404:11, B1404:12, B1404:13 or B1404:1A retrieved on-demand during self-test? 

    1. Yes  : This fault cannot be cleared until it is corrected and the DTC  is no longer retrieved on-demand during self-test.

      For DTC  B1404:13 or B1404:1A, GO to BF2  .

      For DTC  B1404:11, GO to  BF8.

      For DTC  B1404:12, GO to  BF10.

    2. No  : This is an intermittent fault when present as a CMDTC  only.

      For DTC  B1404:13 or B1404:1A, GO to  BF13.

      For DTC  B1404:11, GO to  BF14.

      For DTC  B1404:12, GO to  BF15.

  2. BF2 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PID 
    • Using a scan tool, view RCM PIDs  .
    • Monitor and record the resistance value displayed by the DEPLOY_10_R PID  .

    Does the PID value read between 1.44 and 3.52 ohms? 

    1. Yes  : GO to  BF12.
    2. No  : GO to BF3  .
  3. BF3 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PID WHILE CARRYING OUT THE HARNESS TEST 
    • While monitoring the DEPLOY_10_R PID  , carry out the harness test of the driver seat side airbag module circuits and accessible connectors (including any inline connectors) by wiggling and flexing the wire harness and connectors frequently. Record the resistance value indicated by the PID  .

    Does the PID value read between 1.44 and 3.52 ohms while carrying out the harness test? 

    1. Yes  : DEPOWER the SRS  and REPAIR the connector, terminals or wire harness as needed.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

    2. No  : For PID  value less than 1.44 ohms, GO to BF4  .

      For PID  value greater than 3.52 ohms, GO to  BF6.

  4. BF4 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.

    Did the on-demand DTC change from B1404:1A to B1404:13? 

    1. Yes  : GO to  BF11.
    2. No  : GO to BF5  .
  5. BF5 CHECK FOR A SHORT BETWEEN DRIVER SEAT SIDE AIR BAG CIRCUITS 

    Is the resistance greater than 10, 000 ohms? 

    1. Yes  : GO to  BF12.
    2. No  : REPAIR the circuits.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

  6. BF6 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR AN OPEN 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • For vehicles equipped with the police package, disconnect Driver Seat Side Air Bag Module C3051  .
    • For vehicles not equipped with the police package, disconnect Driver Seat Side Air Bag Module (Inline) C3051  .
    • Disconnect RCM C310A  and C310B  .
    • Measure:
      Positive Lead Measurement/Action Negative Lead
      C310B-40  OHM C3051-1 
      C310B-39  OHM C3051-2 

    Is the resistance less than 0.5 ohm? 

    1. Yes  : GO to BF7  .
    2. No  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

  7. BF7 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Connect RCM C310A  and C310B  .
    • Connect a fused jumper wire:
      Positive Lead Measurement/Action Negative Lead
      C3051-1  FUSED JUMPER WIRE C3051-2 
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .
    • DIAGNOSTIC TIP:  When viewing DTCs  with the driver seat side airbag module circuits shorted together, a low resistance fault is normally retrieved.

    Did the on-demand DTC change from B1404:13 to B1404:1A? 

    1. Yes  : REMOVE the fused jumper wire and GO to  BF11.
    2. No  : REMOVE the fused jumper wire and GO to  BF12.
  8. BF8 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.

    Did the on-demand DTC change from B1404:11 to B1404:13? 

    1. Yes  : GO to  BF11.
    2. No  : GO to BF9  .
  9. BF9 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR A SHORT TO GROUND 

    Are the resistances greater than 10, 000 ohms? 

    1. Yes  : GO to  BF12.
    2. No  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

  10. BF10 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR A SHORT TO VOLTAGE 

    Is any voltage present? 

    1. Yes  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

    2. No  : GO to  BF12.
  11. BF11 CONFIRM THE DRIVER SEAT SIDE AIR BAG MODULE FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : For vehicles equipped with the police package, INSTALL a new driver seat side airbag module. REFER to SIDE AIRBAG . GO to  BF17.

      For vehicles not equipped with the police package, REMOVE and INSPECT the driver seat side airbag module harness for damage. REFER to SIDE AIRBAG . If a concern is found, REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      If a concern was not  found, INSTALL a new driver seat side airbag module. REFER to SIDE AIRBAG . GO to  BF17.

    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  .

      For DTC  B1404:13 or B1404:1A, GO to  BF13.

      For DTC  B1404:11, GO to  BF14.

      For DTC  B1404:12, GO to  BF15.

  12. BF12 CONFIRM THE RCM FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : CHECK OASIS  for any applicable TSBs  . If a TSB  exists for this concern, discontinue this test and follow TSB  instructions. If no TSBs  address this concern, INSTALL a new RCM  . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  BF17.
    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  .

      For DTC  B1404:13 or B1404:1A, GO to BF13  .

      For DTC  B1404:11, GO to  BF14.

      For DTC  B1404:12, GO to  BF15.

  13. BF13 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PID FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT 
    • Using a scan tool, view RCM PIDs  .
    • While monitoring the DEPLOY_10_R PID  , attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently. Record the resistance value indicated by the PID  .

    Does the PID value read between 1.44 and 3.52 ohms? 

    1. Yes  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  BF16.
    2. No  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

  14. BF14 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO GROUND FAULT 
    • Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B1404:11 retrieved on-demand during self-test? 

    1. Yes  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  BF16.
  15. BF15 CHECK THE DRIVER SIDE AIRBAG DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO BATTERY FAULT 

    Was DTC B1404:12 retrieved on-demand during self-test? 

    1. Yes  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  BF17.

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to BF16  .
  16. BF16 CHECK THE HARNESS AND CONNECTORS 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • For vehicles equipped with the police package, disconnect Driver Seat Side Air Bag Module C3051  .
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
    • For vehicles not equipped with the police package, disconnect Driver Seat Side Air Bag Module (Inline) C3051  .
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
    • Inspect RCM C310A  and C310B  CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .

    Were any concerns found? 

    1. Yes  : REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to BF17  .

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to BF17  .
  17. BF17 CHECK FOR ADDITIONAL SRS DTCs 
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

      Ignition OFF.

    • Reconnect all SRS  components (if previously disconnected).
    • If previously directed to depower the SRS  , repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING - WITH INTELLIGENT ACCESS (IA) .
    • Ignition ON.
    • NOTE: When selecting Restraints from the Self-Test menu, DTCs  are retrieved from the RCM  and OCSM  .

      Using a scan tool, perform the Restraints  self-test to retrieve DTCs  .

    Are any RCM and/or OCSM DTCs retrieved on-demand during self-test? 

    1. Yes  : Do not clear any DTCs  until all DTCs  have been resolved. REFER to the appropriate DTC CHART for pinpoint test direction.
    2. No  : CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals