DTC Chart: IPC

DTC DESCRIPTION - IPC

DTC	Description	Action
B1A14:11	RCM Warning Lamp: Circuit Short To Ground	INSTALL a new IPC . Refer to: INSTRUMENT PANEL CLUSTER (IPC) . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). Refer to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
B1A14:13	RCM Warning Lamp: Circuit Open	INSTALL a new IPC . Refer to: INSTRUMENT PANEL CLUSTER (IPC) . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). Refer to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
B1A84:41	Car Configuration Data: General Checksum Failure	This DTC may set after replacement of the IPC . To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. REFER to the Professional Technician Society (PTS) website, run OASIS for any Escape vehicle, select the Service Tips Tab and use the link under the job aids heading labeled BCM programming.
B1A84:51	Car Configuration Data: Not Programmed	This DTC may set after replacement of the IPC . To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. REFER to the Professional Technician Society (PTS) website, run OASIS for any Escape vehicle, select the Service Tips Tab and use the link under the job aids heading labeled BCM programming.
C1D00:00	Park Brake Apply Switch: No Sub Type Information	GO to PINPOINT TEST O
C1D22:11	Steering Wheel Switch Right Module: Circuit Short To Ground	Refer to the appropriate article for the procedure.
C1D22:23	Steering Wheel Switch Right Module: Circuit Open	Refer to the appropriate article for the procedure.
C2003:11	Steering Wheel Switch Left Module: Circuit Short To Ground	GO to PINPOINT TEST AC
C2003:23	Steering Wheel Switch Left Module: Circuit Open	GO to PINPOINT TEST AC
P1607:81	MIL Output Circuit: Invalid Serial Data Received	This DTC sets when the IPC receives an invalid MIL request message for more than 5 seconds. CLEAR the DTC . REPEAT the self-test. If DTC P1607:81 returns, INSTALL a new PCM . Refer to the appropriate article for the procedure.
P1607:82	MIL Output Circuit: Alive/Sequence Counter Incorrect/Not Updated	This DTC sets when the IPC does not receive an updated MIL request message for more than 5 seconds. CLEAR the DTC . REPEAT the self-test. If DTC U0100:00 is also present, GO to PINPOINT TEST AT If DTC P1607:82 returns without DTC U0100:00, INSTALL a new PCM . Refer to the appropriate article for the procedure.
P1607:87	MIL Output Circuit: Missing Message	This DTC sets when the IPC does not receive updated MIL request message for more than 5 seconds. CLEAR the DTC . REPEAT the self-test. If DTC U0100:00 is also present, GO to PINPOINT TEST AT If DTC P1607:87 returns without DTC U0100:00, INSTALL a new PCM . Refer to the appropriate article for the procedure.
P1706:00	High Vehicle Speed Observed in Park: No Sub Type Information	GO to PINPOINT TEST X
P1933:68	Fuel Level Signal: Event Information	GO to PINPOINT TEST B
U0073:00	Control Module Communication Bus "A" Off: No Sub Type Information	Refer to: COMMUNICATIONS NETWORK .
U0074:00	Control Module Communication Bus "B" Off: No Sub Type Information	Refer to: COMMUNICATIONS NETWORK .
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to PINPOINT TEST AT
U0101:00	Lost Communication With TCM: No Sub Type Information	GO to PINPOINT TEST AU
U0121:00	Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	GO to PINPOINT TEST AV
U0131:00	Lost Communication With Power Steering Control Module: No Sub Type Information	GO to PINPOINT TEST AW
U0140:00	Lost Communication With Body Control Module: No Sub Type Information	GO to PINPOINT TEST AX
U0151:00	Lost Communication With Restraints Control Module: No Sub Type Information	GO to PINPOINT TEST AY
U0159:00	Lost Communication With Parking Assist Control Module "A": No Sub Type Information	GO to PINPOINT TEST AZ
U0164:00	Lost Communication With HVAC Control Module: No Sub Type Information	GO to PINPOINT TEST BA
U0184:00	Lost Communication With Radio: No Sub Type Information	GO to PINPOINT TEST BB
U0208:00	Lost Communication With "Seat Control Module B": No Sub Type Information	GO to PINPOINT TEST BC
U0214:00	Lost Communication With Remote Function Actuator: No Sub Type Information	GO to PINPOINT TEST BD
U0232:00	Lost Communication With Side Obstacle Detection Control Module-Left: No Sub Type Information	GO to PINPOINT TEST BE
U0233:00	Lost Communication With Side Obstacle Detection Control Module-Right: No Sub Type Information	GO to PINPOINT TEST BE
U0252:00	Lost Communication With Lighting Control Module-Rear "B": No Sub Type Information	GO to PINPOINT TEST BF
U0257:00	Lost Communication With Front Controls/Display Interface Module: No Sub Type Information	GO to PINPOINT TEST BG
U0264:00	Lost Communication With Camera Module-Rear: No Sub Type Information	GO to PINPOINT TEST BH
U0401:64	Invalid Data Received From ECM/PCM A: Signal Plausibility Failure	This DTC sets when a message is temporarily undefined for more than 2 seconds from the PCM for the ambient temperature, fuel economy, engine coolant temperature or engine RPM data. CLEAR the DTC . REPEAT the self-test. If DTC U0401:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PCM . Refer to the appropriate article for the procedure.
U0415:64	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Plausibility Failure	This DTC sets when the wheel rotation count message is temporarily undefined for more than 2 seconds from the ABS module for the odometer. CLEAR the DTC . REPEAT the self-test. If DTC U0415:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the ABS module. Refer to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL .
U0420:68	Invalid Data Received From Power Steering Control Module: Event Information	This DTC sets when data is invalid from the PSCM . CLEAR the DTC . REPEAT the self-test. If DTC U0420:68 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PSCM . Refer to: POWER STEERING .
U0422:00	Invalid Data or Missing Data Received From Body Control Module: No Sub Type Information	This DTC sets when the fuel level, power mode or vehicle speed message are temporarily undefined for more than 2 seconds or if the TPMS status message is missing for more than 1, 250 milliseconds from the BCM . CLEAR the DTC . REPEAT the self-test. If DTC U0422:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM . Refer to: BODY CONTROL MODULE (BCM) .
U0422:68	Invalid Data or Missing Data Received From Body Control Module: Event Information	This DTC sets when data is invalid from the BCM . CLEAR the DTC . REPEAT the self-test. If DTC U0422:68 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM . Refer to: BODY CONTROL MODULE (BCM) .
U0424:00	Invalid Data Received From HVAC Control Module: No Sub Type Information	This DTC sets when the temperature range data is invalid for more than 2 seconds from the HVAC module through the BCM . CLEAR the DTC . REPEAT the self-test. If DTC U0424:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the HVAC module. With DATC , Refer to: CLIMATE CONTROL SYSTEM - VEHICLES WITH: DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) . With EMTC , Refer to: CLIMATE CONTROL SYSTEM - VEHICLES WITH: ELECTRONIC MANUAL TEMPERATURE CONTROL (EMTC) .
U0452:00	Invalid Data Received From Restraints Control Module: No Sub Type Information	This DTC sets when data is invalid from the RCM . CLEAR the DTC . REPEAT the self-test. If DTC U0452:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the RCM . Refer to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
U0558:00	Invalid Data Received From Front Controls/Display Interface Module: No Sub Type Information	This DTC sets when data is invalid from the FCDIM for longer than 2 seconds. CLEAR the DTC . REPEAT the self-test. If DTC U0558:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the FCDIM. Refer to the appropriate article for the procedure.
U0564:00	Invalid Data Received From Speech Recognition Module: No Sub Type Information	This DTC sets when data is invalid from the APIM for longer than 2 seconds. CLEAR the DTC . REPEAT the self-test. If DTC U0564:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the APIM . Refer to the appropriate article for the procedure.
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U2101:01	Control Module Configuration Incompatible: General Electrical Failure	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U3000:41	Control Module: General Checksum Failure	CLEAR the DTC . REPEAT the self-test. If DTC U3000:41 returns, INSTALL a new IPC . Refer to: INSTRUMENT PANEL CLUSTER (IPC) .
U3000:44	Control Module: Data Memory Failure	CLEAR the DTC . REPEAT the self-test. If DTC U3000:44 returns, INSTALL a new IPC . Refer to: INSTRUMENT PANEL CLUSTER (IPC) .
U3006:16	Control Module Input Power "A": Circuit Voltage Below Threshold	GO to PINPOINT TEST BI
U3006:17	Control Module Input Power "A": Circuit Voltage Above Threshold	GO to PINPOINT TEST BJ