The FDIM (Front Display Interface Module) Displays An Active Park Assist Fault Message

F1 PERFORM A NETWORK TEST
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Do all modules pass the network test?
- Yes : GO to F2
- No : REFER to: COMMUNICATIONS NETWORK .
F2 CHECK THE PARKING AID MODULE (PAM) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the Parking Aid Module (PAM) self-test.
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: PARKING AID .
- No : GO to F3
F3 CHECK THE PSCM (POWER STEERING CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PSCM self-test.
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: POWER STEERING .
- No : GO to F4
F4 CHECK THE SCCM (STEERING COLUMN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the SCCM self-test.
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: STEERING WHEEL AND COLUMN ELECTRICAL COMPONENTS .
- No : GO to F5
F5 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the ABS module self-test.
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL .
- No : GO to F6
F6 CHECK THE PCM (POWERTRAIN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PCM self-test.
Are any Diagnostic Trouble Codes present?
- Yes : Refer to the appropriate Engine Mechanical article for the procedure.
- No : GO to F7
F7 CHECK THE FCIM (FRONT CONTROLS INTERFACE MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the FCIM self-test.
Are any Diagnostic Trouble Codes present?
- Yes : Vehicles equipped with Sony® sound,
  REFER to: INFORMATION AND ENTERTAINMENT SYSTEM - Vehicles With: AM/FM/CD/SYNC/Sony Audio System .
  
  Vehicles not equipped with Sony® sound,
  
  REFER to: INFORMATION AND ENTERTAINMENT SYSTEM - Vehicles With: AM/FM/CD/SYNC/Touchscreen Display .
- No : GO to F8
F8 CHECK THE BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the BCM self-test.
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: BODY CONTROL MODULE (BCM) .
- No : GO to F9
F9 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)
- Ignition OFF.
- Ignition ON.
- Operate the system to determine if the concern is still present.
- Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Are any Diagnostic Trouble Codes present?
- Yes : REFER to: COMMUNICATIONS NETWORK .
- No : GO to F10
F10 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all BCM connectors.
- Repair:
  - corrosion (install new connector or terminals - clean module pins)
  - damaged or bent pins - install new terminals/pins
  - pushed-out pins - install new pins as necessary
- Reconnect the BCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
- Yes : CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a Technical Service Bulletin (TSB) exists for this concern, DISCONTINUE this test and FOLLOW Technical Service Bulletin (TSB) instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM .
  REFER to: BODY CONTROL MODULE (BCM) .
- No : The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.