LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2013 >> Focus Titanium, 4D Sedan, Standard Trans, Gas >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Except Electric) - Pinpoint Tests (B0004 - B11D8) >> Pinpoint Test - Vehicles Built Up To: 25-June-2012, DTC: B0052:11, B0052:12, B0052:13 and B0052:1D >> B0052:11, B0052:12, B0052:13 and B0052:1D >> Normal Operation and Fault Conditions >> Pinpoint Test A : B0052:11, B0052:12, B0052:13 And B0052:1D

Pinpoint Test A : B0052:11, B0052:12, B0052:13 And B0052:1D

WARNING: Do not handle, move or change the original horizontal mounting position of the Restraints Control Module (RCM) while the Restraints Control Module (RCM) is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy® and cause serious personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS) 

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-dem and during self-test? 

    1. Yes:  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-dem and during self-test.

      For DTC B0052:11 or B0052:1D, GO to A2

      For DTC B0052:12, GO to  A4

      For DTC B0052:13, GO to  A5

    2. No:  This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to  A10
  2. A2 CHECK THE PASSENGER SEATBELT SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect Passenger Safety Belt Buckle Switch (Inline) C3007J.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.
    • DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the passenger safety belt buckle switch disconnected, an open circuit fault is normally retrieved. Due to the inline connector being disconnected, a fault is also normally retrieved for the OCS, passenger seat track position sensor and passenger side air bag circuits.

    Did the on-demand DTC change from B0052:11 or B0052:1D to B0052:13? 

    1. Yes:  GO to  A8
    2. No:  For DTC B0052:11, GO to A3

      For DTC B0052:1D, GO to  A9

  3. A3 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO GROUND 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C3007J-1 Ω -

    Is the resistance greater than 10, 000 ohms? 

    1. Yes:  GO to  A9
    2. No:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A11

  4. A4 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO VOLTAGE 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C3007J-1
    G08101543
    		 -

    Is any voltage present? 

    1. Yes:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A11

    2. No:  GO to  A9
  5. A5 CHECK THE PASSENGER SEATBELT SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C3007J-1
    G08101544
    		 C3007J-2
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.
    • DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the passenger safety belt buckle switch circuits shorted together, a short to ground fault is normally retrieved. Due to the inline connector being disconnected, a fault is also normally retrieved for the OCS, passenger seat track position sensor and passenger side air bag circuits.

    Did the on-demand DTC change from B0052:13 to B0052:11? 

    1. Yes:  REMOVE the fused jumper wire and GO to  A8
    2. No:  REMOVE the fused jumper wire and GO to A6
  6. A6 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR AN OPEN 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C310B-25 Ω C3007J-1

    Is the resistance less than 0.5 ohm? 

    1. Yes:  GO to A7
    2. No:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A11

  7. A7 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH GROUND CIRCUIT FOR AN OPEN 
    • Measure:

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C3007J-2 Ω C310B-34

    Is the resistance less than 3 ohms? 

    1. Yes:  GO to  A9
    2. No:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A11

  8. A8 CONFIRM THE PASSENGER SAFETY BELT BUCKLE SWITCH FAULT 
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

        REFER to: Restraints Control Module (RCM) .

      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B (if previously disconnected).
    • Connect Passenger Safety Belt Buckle Switch (Inline) C3007J.
      • Tighten to 1 Nm (9 lb-in).
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was the original DTC retrieved on-dem and during self-test? 

    1. Yes:  INSTALL a new passenger safety belt buckle.

      REFER to: FRONT SAFETY BELT BUCKLE .

      GO to  A11

    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A10
  9. A9 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT 
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

        REFER to: Restraints Control Module (RCM) .

      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B (if previously disconnected).
    • Connect Passenger Safety Belt Buckle Switch (Inline) C3007J.
      • Tighten to 1 Nm (9 lb-in).
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition OFF.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was the original DTC retrieved on-dem and during self-test? 

    1. Yes:  CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM.

      REFER to: Restraints Control Module (RCM) .

      GO to  A11

    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A10
  10. A10 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect Passenger Safety Belt Buckle Switch (Inline) C3007J.
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

      REFER to: Restraints Control Module (RCM) .

    • Connect all previously disconnected component(s)/connector(s).
      • For Passenger Safety Belt Buckle Switch (Inline) C3007J, tighten to 1 Nm (9 lb-in).
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Using a scan tool, perform RCM self-test to retrieve Diagnostic Trouble Codes (DTCs).

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-dem and during self-test? 

    1. Yes:  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-dem and during self-test.

      For DTC B0052:11 or B0052:1D, GO to  A2

      For DTC B0052:12, GO to  A4

      For DTC B0052:13, GO to  A5

    2. No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A11
  11. A11 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS) 
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Ignition OFF.
    • Reconnect all SRS components (if previously disconnected).
    • If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - Restraints.
      NOTE: When selecting Restraints from the Self Test menu, Diagnostic Trouble Codes (DTCs) are retrieved from the RCM and OCSM.

    Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-dem and during self-test? 

    1. Yes:  Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. Refer to RCM DTC CHART or Refer to OCSM DTC CHART for pinpoint test direction.
    2. No:  CLEAR Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules. PROVE OUT the SRS. The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals