LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2013 >> Focus Titanium, 4D Sedan, Standard Trans, Gas >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Except Electric) - Pinpoint Tests (B0001 - B0052) >> Pinpoint Test - DTC: B0020:11, B0020:12, B0020:13 and B0020:1A >> Diagnostic Overview >> B0020:11, B0020:12, B0020:13 and B0020:1A >> Pinpoint Test A : B0020:11, B0020:12, B0020:13 And B0020:1A

Pinpoint Test A : B0020:11, B0020:12, B0020:13 And B0020:1A

WARNING: Do not handle, move or change the original horizontal mounting position of the Restraints Control Module (RCM) while the Restraints Control Module (RCM) is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy® and cause serious personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS) 

    Was DTC B0020:11, B0020:12, B0020:13 or B0020:1A retrieved on-dem and during self-test? 

    1. Yes:  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-dem and during self-test.

      For DTC B0020:13 or B0020:1A, GO to A2 

      For DTC B0020:11, GO to  A8

      For DTC B0020:12, GO to  A10

    2. No:  This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only.

      For DTC B0020:13 or B0020:1A, GO to  A13

      For DTC B0020:11, GO to  A14

      For DTC B0020:12, GO to  A15

  2. A2 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PARAMETER IDENTIFICATION (PID) 
    • Using a diagnostic scan tool, view RCM Parameter Identifications (PIDs).
    • Monitor and record the resistance value displayed by the DEPLOY_10_R Parameter Identification (PID).

    Does the Parameter Identification (PID) value read between 1.7 and 2.78 ohms? 

    1. Yes:  GO to  A12
    2. No:  GO to A3 
  3. A3 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PARAMETER IDENTIFICATION (PID) WHILE CARRYING OUT THE HARNESS TEST 
    • While monitoring the DEPLOY_10_R Parameter Identification (PID), carry out the harness test of the driver seat side airbag circuits and accessible connectors (including any inline connectors) by wiggling and flexing the wire harness and connectors frequently. Record the resistance value indicated by the Parameter Identification (PID).

    Does the Parameter Identification (PID) value read between 1.7 and 2.78 ohms while carrying out the harness test? 

    1. Yes:  DEPOWER the SRS and REPAIR the connector, terminals or wire harness as needed.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

    2. No:  For Parameter Identification (PID) value less than 1.7 ohms, GO to A4 

      For Parameter Identification (PID) value greater than 2.78 ohms, GO to  A6

  4. A4 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect Driver Seat Side Airbag (Inline) C300B.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the driver seat side airbag disconnected, an open circuit fault is normally retrieved. Due to the inline seat connector being disconnected, Diagnostic Trouble Codes (DTCs) will also set for the seat track position sensor and safety belt buckle switch.

    Did the on-demand DTC change from B0020:1A to B0020:13? 

    1. Yes:  GO to  A11
    2. No:  GO to A5 
  5. A5 CHECK FOR A SHORT BETWEEN DRIVER SEAT SIDE AIR BAG CIRCUITS 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C300B-1 Ω C300B-2

    Is the resistance greater than 10, 000 ohms? 

    1. Yes:  GO to  A12
    2. No:  REPAIR the circuits.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

  6. A6 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR AN OPEN 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C310B-20 Ω C300B-1
    C310B-19 Ω C300B-2

    Are the resistances less than 0.5 ohm? 

    1. Yes:  GO to A7 
    2. No:  REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

  7. A7 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Connect RCM C310A and C310B.
    • Connect a fused jumper wire:

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C300B-1
    G08101461
    		 C300B-2
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the driver seat side airbag circuits shorted together, a low resistance fault is normally retrieved. Due to the inline seat connector being disconnected, Diagnostic Trouble Codes (DTCs) will also set for the seat track position sensor and safety belt buckle switch.

    Did the on-demand DTC change from B0020:13 to B0020:1A? 

    1. Yes:  REMOVE the fused jumper wire and GO to  A11
    2. No:  REMOVE the fused jumper wire and GO to  A12
  8. A8 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect Driver Seat Side Airbag (Inline) C300B.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the driver seat side airbag disconnected, an open circuit fault is normally retrieved. Due to the inline seat connector being disconnected, Diagnostic Trouble Codes (DTCs) will also set for the seat track position sensor and safety belt buckle switch.

    Did the on-demand DTC change from B0020:11 to B0020:13? 

    1. Yes:  GO to  A11
    2. No:  GO to A9 
  9. A9 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR A SHORT TO GROUND 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C300B-1 Ω -
    C300B-2 Ω -

    Are the resistances greater than 10, 000 ohms? 

    1. Yes:  GO to  A12
    2. No:  REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

  10. A10 CHECK THE DRIVER SEAT SIDE AIR BAG CIRCUITS FOR A SHORT TO VOLTAGE 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C300B-1
    G08101462
    		 -
    C300B-2
    G08101463
    		 -

    Is any voltage present? 

    1. Yes:  REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

    2. No:  GO to  A12
  11. A11 CONFIRM THE DRIVER SEAT SIDE AIR BAG MODULE FAULT 
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

    Was the original DTC retrieved on-dem and during self-test? 

    1. Yes:  REMOVE and INSPECT the driver seat side airbag harness for damage.

      REFER to: Side Airbag .

      If a concern is found, REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

      If a concern is not found, INSTALL a new driver seat side airbag.

      REFER to: Side Airbag .

      GO to  A17

    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test.

      For DTC B0020:13 or B0020:1A, GO to  A13

      For DTC B0020:11, GO to  A14

      For DTC B0020:12, GO to  A15

  12. A12 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT 
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

    Was the original DTC retrieved on-dem and during self-test? 

    1. Yes:  CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM.

      REFER to: Restraints Control Module (RCM) .

      GO to  A17

    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test.

      For DTC B0020:13 or B0020:1A, GO to A13 

      For DTC B0020:11, GO to  A14

      For DTC B0020:12, GO to  A15

  13. A13 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_10_R) PARAMETER IDENTIFICATION (PID) FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT 
    • Using a diagnostic scan tool, view RCM Parameter Identifications (PIDs).
    • While monitoring the DEPLOY_10_R Parameter Identification (PID), attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently. Record the resistance value indicated by the Parameter Identification (PID).

    Does the Parameter Identification (PID) value read between 1.7 and 2.78 ohms? 

    1. Yes:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A16
    2. No:  DEPOWER the SRS and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

  14. A14 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO GROUND FAULT 
    • Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B0020:11 retrieved on-dem and during self-test? 

    1. Yes:  DEPOWER the SRS and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

    2. No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A16
  15. A15 CHECK THE LEFT SIDE AIRBAG DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO BATTERY FAULT 

    Was DTC B0020:12 retrieved on-dem and during self-test? 

    1. Yes:  DEPOWER the SRS and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A17

    2. No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A16 
  16. A16 CHECK THE HARNESS AND CONNECTORS 
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect Driver Seat Side Airbag (Inline) C300B.
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
    • Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

      REFER to: Restraints Control Module (RCM) .

    Were any concerns found? 

    1. Yes:  REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to A17 

    2. No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A17 
  17. A17 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS) 
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Ignition OFF.
    • Reconnect all SRS components (if previously disconnected).
    • If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
      • NOTE: When selecting Restraints from the Self Test menu, Diagnostic Trouble Codes (DTCs) are retrieved from the RCM and OCSM.
    • Using a diagnostic scan tool, perform Restraints  self-test.

    Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-dem and during self-test? 

    1. Yes:  Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. Refer to RCM DTC CHART or Refer to OCSM DTC CHART for pinpoint test direction.
    2. No:  CLEAR Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules. PROVE OUT the SRS. The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals