Pinpoint Test Ar: The Safety Belt Warning Chime Or Belt-Minder® Feature Chime Is Inoperative Or Always On
- AR1 CHECK THE HEADLAMPS ON WARNING CHIME OPERATION
- Ignition OFF.
- Close the LH front dooor.
- Place the headlamp switch in the HEADLAMP or PARKING LAMP position.
- Open the LH front door and observe the headlamps on warning chime operation.
- Turn the headlamps/parklamps off.
- Does the headlamps on warning chime sound with the headlamps/parking lamps on and the LH front door open and turn off with the headlamps/parking lamps off?
- Yes : GO to AR2.
- No : INSTALL a new IPC. REFER to INSTRUMENT PANEL CLUSTER (IPC) .
- AR2 CHECK THE SPEEDOMETER OPERATION
- Verify that the speedometer is operating correctly.
- Does the speedometer operate correctly?
- Yes : GO to AR3.
- No : GO to PINPOINT TEST E .
- AR3 RETRIEVE THE RECORDED DTCs FROM THE IPC SELF-TEST
- Using a scan tool, perform the IPC self-test.
- Are any DTCs recorded?
- Yes
: For DTC U0140:00, GO to PINPOINT TEST AX .
For DTC U0151:00, GO to PINPOINT TEST AY .
For all other DTCs, REFER to DTC Chart - IPC .
- No : GO to AR4.
- AR4 RETRIEVE THE RECORDED DTCs FROM THE BCM SELF-TEST
- Check for recorded BCM DTCs from the self-test.
- Are any DTCs recorded?
- Yes : REFER to MULTIFUNCTION ELECTRONIC MODULES .
- No : GO to AR5.
- AR5 RETRIEVE THE RECORDED DTCs FROM THE RCM SELF-TEST
- Check for recorded RCM DTCs from the self-test.
- Are any DTCs recorded?
- Yes : REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
- No : GO to AR6.
- AR6 CHECK THE DRIVER AND FRONT PASSENGER SAFETY BELT BUCKLE SWITCHES
- Ignition ON.
- Using a scan tool, view the RCM PIDs.
- Select and monitor the RCM driver safety belt buckle (SBLT_D_ST) PID and the front passenger safety belt buckle (SBLT_P_ST) PID while buckling and unbuckling the driver and front passenger safety belts.
- Do the PIDs display BUCKLED with the safety belt buckled and UNBUCKLED with the safety belt unbuckled?
- Yes : GO to AR7.
- No : REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
- AR7 CHECK THE SAFETY BELT WARNING INDICATOR FOR CORRECT OPERATION
- Ignition OFF.
- Ignition ON.
- Within one minute, buckle then unbuckle the LH front safety belt.
- Verify the safety belt warning indicator illuminates with the safety belt unbuckled and turns off when buckled.
- Does the safety belt warning indicator operate correctly?
- Yes : GO to AR8.
- No : GO to PINPOINT TEST V .
- AR8 CHECK THE BELT-MINDER® CONFIGURATION NOTE: Verify that an administrator key is used for this test and not a MyKey® programmed key. When a MyKey® programmed key is used, the Belt-Minder® is automatically turned on and cannot be disabled (if previously disabled by an administrator, the Belt-Minder® remains disabled when an administrator key is used).
- Verify that the Belt-Minder® is activated or configured on for the seating position in question. Refer to BELT-MINDER® DEACTIVATING/ACTIVATING to configure without a scan tool.
- Is the Belt-Minder® activated for the seating position in question?
- Yes : If the Belt-Minder® is always on above 10 km/h (6 mph) with the safety belt unfastened, the system is operating correctly. If the Belt-Minder® is always on with the safety belt fastened or never on with the safety belt unfastened above 10 km/h (6 mph), INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
- No : ACTIVATE the Belt-Minder® for the seating position in question. REFER to BELT-MINDER® DEACTIVATING/ACTIVATING .