LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2013 >> Edge SEL, 2.0L Eng VIN 9 >> Repair and Diagnosis >> External Pages >> Different car >> Section 234 (Supplemental Restraint System) >> Diagnosis And Testing >> Airbag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test - Restraints Control Module (RCM) >> Pinpoint Test J: DTCs B0052:11, B0052:12, B0052:13 and B0052:1D >> PINPOINT TEST J: DTCs B0052:11, B0052:12, B0052:13 AND B0052:1D

PINPOINT TEST J: DTCs B0052:11, B0052:12, B0052:13 AND B0052:1D

WARNING: This page is about a different car, the 2014 Lincoln MKX and 2014 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy and cause serious personal injury or death.
WARNING: Never disassemble or tamper with seat belt deployable components, including pretensioners, load limiters and inflators. Never back probe deployable device electrical connectors. Tampering or back probing may cause an accidental deployment and result in personal injury or death.
WARNING: Never probe the electrical connectors on airbag, Safety Canopy or side air curtain assemblies. Failure to follow this instruction may result in the accidental deployment of these assemblies, which increases the risk of serious personal injury or death.
NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough INSPECTION AND VERIFICATION  before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect Supplemental Restraint System (SRS) components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
  1. J1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-demand during self-test? 

    • Yes  : This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      For DTC B0052:11 or B0052:1D, GO to J2  .

      For DTC B0052:12, GO to  J4.

      For DTC B0052:13, GO to  J5.

    • No  : This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to  J10.
  2. J2 CHECK THE PASSENGER SEATBELT SENSOR DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Disconnect: Passenger Safety Belt Buckle Switch C3066  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger safety belt buckle switch disconnected, an open circuit fault is normally retrieved.

    Did the on-demand DTC change from B0052:11 or B0052:1D to B0052:13? 

    • Yes  : GO to  J8.
    • No  : For DTC B0052:11, GO to J3  .

      For DTC B0052:1D, GO to  J9.

  3. J3 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Disconnect: RCM C310A  and C310B  .
    • Measure the resistance between passenger safety belt buckle switch C3066-2  , circuit CR203 (GY/VT), harness side and ground.
      Fig 1: Measuring Resistance Between Passenger Safety Belt Buckle Switch C3066-2, Circuit CR203 (GY/VT), Harness Side And Ground
      G06404103Courtesy of FORD MOTOR CO.

    Is the resistance greater than 10, 000 ohms? 

  4. J4 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO VOLTAGE 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Disconnect: Passenger Seat Side Air Bag Module C327  .
    • Disconnect: Passenger Safety Belt Buckle Switch C3066  .
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Measure the voltage between passenger safety belt buckle switch C3066-2  , circuit CR203 (GY/VT), harness side and ground.
      Fig 2: Measuring Voltage Between Passenger Safety Belt Buckle Switch C3066-2, Circuit CR203 (GY/VT), Harness Side And Ground
      G06404104Courtesy of FORD MOTOR CO.

    Is any voltage present? 

  5. J5 CHECK THE PASSENGER SEATBELT SENSOR DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Disconnect: Passenger Seat Side Air Bag Module C327  .
    • Disconnect: Passenger Safety Belt Buckle Switch C3066  .
    • Connect a fused jumper wire between passenger safety belt buckle switch C3066-1  , circuit GD143 (BK/VT), harness side, and passenger safety belt buckle switch C3066-2  , circuit CR203 (GY/VT), harness side.
      Fig 3: Connecting Fused Jumper Wire Between Driver Safety Belt Buckle Switch C3065-1, Circuit GD143 (BK/VT) And Driver Safety Belt Buckle Switch C3065-2, Circuits CR201 (GN/BU)
      G07399500Courtesy of FORD MOTOR CO.
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger safety belt buckle switch circuits shorted together, a short to ground fault is normally retrieved.

    Did the on-demand DTC change from B0052:13 to B0052:11? 

    • Yes  : REMOVE the fused jumper wire and GO to  J8.
    • No  : REMOVE the fused jumper wire and GO to J6  .
  6. J6 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Disconnect: RCM C310A  and C310B  .
    • Measure the resistance between RCM C310B-33  , circuit CR203 (GY/VT), harness side and the passenger safety belt buckle switch C3066-2  , circuit CR203 (GY/VT), harness side.
      Fig 4: Measuring Resistance Between RCM C310B-34, Circuit CR201 (GN/BU) And Driver Safety Belt Buckle C3296-2, Circuit CR201 (GN/BU), Harness Side
      G06404105Courtesy of FORD MOTOR CO.

    Is the resistance less than 0.5 ohm? 

  7. J7 CHECK THE PASSENGER SAFETY BELT BUCKLE SWITCH GROUND CIRCUIT FOR AN OPEN 
    • Measure the resistance between passenger safety belt buckle switch C3066-1  , circuit GD143 (BK/VT), harness side and ground.
      Fig 5: Measuring Resistance Between Passenger Safety Belt Buckle Switch C3066-1, Circuit GD143 (BK/VT), Harness Side And Ground
      G06404106Courtesy of FORD MOTOR CO.

    Is the resistance less than 5 ohms? 

  8. J8 CONFIRM THE PASSENGER SAFETY BELT BUCKLE SWITCH FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Prior to reconnecting any previously disconnected SRS  component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A  and C310B  Connector Position Assurance (CPA) lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM)  .
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect: RCM C310A  and C310B  (if previously disconnected).
    • Connect: Passenger Seat Side Air Bag Module C327  (if previously disconnected).
    • Connect: Passenger Safety Belt Buckle Switch C3066  .
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .

    Was the original DTC retrieved on-demand during self-test? 

    • Yes  : INSTALL a new passenger safety belt buckle. REFER to SAFETY BELT SYSTEM . GO to  J11.
    • No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  J10.
  9. J9 CONFIRM THE RCM FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Prior to reconnecting any previously disconnected SRS  component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect C310A  and C310BCPA  lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM)  .
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect: Passenger Safety Belt Buckle Switch C3066  .
    • Connect: RCM C310A  and C310B  (if previously disconnected).
    • Connect: Passenger Seat Side Air Bag Module C327  (if previously disconnected).
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .

    Was the original DTC retrieved on-demand during self-test? 

    • Yes  : INSTALL a new RCM  . REFER to RESTRAINTS CONTROL MODULE (RCM)  . GO to  J11.
    • No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to J10  .
  10. J10 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Disconnect: Passenger Safety Belt Buckle Switch C3066  .
      • inspect connector(s) (including any in-line connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect: All previously disconnected component(s)/connector(s).
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-demand during self-test? 

    • Yes  : This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      For DTC B0052:11 or B0052:1D, GO to  J2.

      For DTC B0052:12, GO to  J4.

      For DTC B0052:13, GO to  J5.

    • No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to J11  .
  11. J11 CHECK FOR ADDITIONAL SRS DTCs 
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Reconnect all SRS  components (if previously disconnected).
    • If previously directed to depower the SRS  , repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING  .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - Restraints.
      NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM  and OCSM  .

    Are any RCM and/or OCSM DTCs retrieved on-demand during self-test? 

    • Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the DTC CHARTS  for pinpoint test direction.
    • No  : CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals