Intermediate Clutch System

WARNING: This page is about a different car, the 2014 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.

For intermediate (2, 6) clutch operation, REFER to AUTOMATIC TRANSMISSION .

Item	Part Number	Description
1	7005	Transmission case
2	7E005	Intermediate clutch piston
3	7B070	Intermediate clutch piston return spring
4	7D483	Intermediate clutch piston return spring snap ring
5	7E005	Intermediate clutch apply ring
6	7A019	Rear planetary sun gear and shell assembly
7	7E085	Intermediate clutch wave spring
8	7B165	Intermediate clutch assembly
9	7A089	Low/OWC

INTERMEDIATE CLUTCH SYSTEM DESCRIPTION

Condition	Possible Sources	Action
Intermediate (2, 6) clutch does not apply	Solenoid filter blocked to SSC	REFER to SOLENOIDS .
	SSC mechanically stuck OFF	INSTALL a new SSC . REFER to SOLENOIDS .
	Intermediate (2, 6) clutch regulator valve stuck OFF	DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control. REFER to MAIN CONTROL - OVERHAUL .
	SSC SIG, CB26, CB26FD/CB1234FD hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control and separator plate passages for debris/blockage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	CB26 supply hydraulic circuit blocked or leaking	DISASSEMBLE and INSPECT the transmission cover passages for debris/blockage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	Rear planetary sun gear and shell assembly	INSPECT the sun gear and shell for wear and damage. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch friction plates	DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch piston seal leakage	INSTALL a new intermediate (2, 6) clutch piston and seals. REFER to TRANSAXLE - OVERHAUL .
Intermediate (2, 6) clutch always applied	Solenoid filter or seal damaged at SSC	REFER to SOLENOIDS .
	SSC mechanically stuck ON	INSTALL a new SSC . REFER to SOLENOIDS .
	Intermediate (2, 6) clutch regulator valve stuck ON	DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and bias spring. If bore or valve is damaged, INSTALL a new main control. REFER to MAIN CONTROL - OVERHAUL .
	SSC SIG, CB26, CB26FD/CB1234FD hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for leakage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	Rear planetary sun gear and shell assembly	INSPECT the sun gear and shell for damage that would prevent free rotation. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch friction plates	DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch piston return spring.	INSPECT the return spring for damage. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
Intermediate (2, 6) clutch delayed/soft/slipping apply	Incorrect Solenoid Body Strategy programmed into TCM	REFER to SOLENOID BODY STRATEGY DOWNLOAD .
	Solenoid filter or seal damaged at SSC	REFER to SOLENOIDS .
	SSC mechanically sticking	INSTALL a new SSC . REFER to SOLENOIDS .
	Intermediate (2, 6) clutch regulator valve sticking	DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control. REFER to MAIN CONTROL - OVERHAUL .
	SSC SIG, CB26, CB26FD/CB1234FD hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control and separator plate passages for debris/blockage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	CB26 supply hydraulic circuit blocked or leaking	DISASSEMBLE and INSPECT the transmission cover passages for debris/blockage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	Intermediate (2, 6) clutch friction plates	DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch piston seal leakage	INSTALL a new intermediate (2, 6) clutch piston and seals. REFER to TRANSAXLE - OVERHAUL .
Intermediate (2, 6) clutch harsh apply	Incorrect Solenoid Body Strategy programmed into TCM	REFER to SOLENOID BODY STRATEGY DOWNLOAD .
	SSC mechanically sticking	INSTALL a new SSC . REFER to SOLENOIDS .
	Intermediate (2, 6) clutch regulator valve sticking	DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and bias spring. If bore, valve or spring is damaged, INSTALL a new main control. REFER to MAIN CONTROL - OVERHAUL .
	SSC SIG, CB26, CB26FD/CB1234FD hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to MAIN CONTROL - OVERHAUL .
	Intermediate (2, 6) clutch friction plates	DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .
	Intermediate (2, 6) clutch piston return spring	INSPECT the return spring for proper installation and damage. INSTALL new components as necessary. REFER to TRANSAXLE - OVERHAUL .