LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2013 >> Edge SEL, 2.0L Eng VIN 9 >> Repair and Diagnosis >> External Pages >> Different car >> Section 217 (Engine Mechanical - 2.0L GTDI) >> In-Vehicle Repair >> Oil Pump >> Installation

Oil Pump: Installation

WARNING: This page is about a different car, the 2014 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
  1. NOTE: Clean the oil pump and cylinder block mating surfaces with metal surface prep.

    Install the oil pump assembly. Tighten the 4 bolts in the sequence shown in 2 stages in illustration:

    • Stage 1: Tighten to 10 Nm (89 lb-in).
    • Stage 2: Tighten to 20 Nm (177 lb-in).
      G08028702
  2. Install the oil pump sprocket and bolt.
    • Tighten to 25 Nm (18 lb-ft).
      G08028700
  3. Install the chain on the oil pump sprocket.
    1. Install the tensioner and the 2 shoulder bolts.
      • Tighten to 10 Nm (89 lb-in).
    2. Push the tensioner spring down and position the spring under the shoulder bolt.
      G08028704
  4. Install the oil pump screen and pickup tube and the 2 bolts.
    • Tighten to 10 Nm (89 lb-in).
      G08028705
  5. NOTE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges, which make leak paths. Use a plastic scraping tool to remove traces to sealant.

    Clean all the oil pan and cylinder block mating surfaces with metal surface prep.

  6. NOTE: If the oil pan is not secured within 10 minutes of sealant application, the sealant must be removed and the sealing area cleaned with metal surface prep. Allow to dry until there is no sign of wetness, or 10 minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.

    Apply a 3 mm (0.118 in) bead of silicone gasket and sealant to the oil pan-to-engine block mating surface.

    G08028706
  7. NOTE: Do not tighten the oil pan bolts at this time.

    Position the oil pan onto the engine and install the 13 bolts finger-tight.

    G08028697
  8. Using a suitable straight edge, align the front surface of the oil pan flush with the front surface of the engine block.
    G08028708
  9. Tighten in the sequence shown in illustration to 20 Nm (177 lb-in).
    G08028709
  10. Install the oil pan-to-bellhousing bolt.
    • Tighten to 48 Nm (35 lb-ft).
      G08028671
  11. Install the 3 bellhousing-to-oil pan bolts.
    • Tighten to 48 Nm (35 lb-ft).
      G08028670
  12. Install the A/C compressor, the 2 bolts and the stud.
    • Tighten the bolts to 25 Nm (18 lb-ft) and the stud to 9 Nm (80 lb-in).
    • Install the nut and tighten to 25 Nm (18 lb-ft).
      G08028668
  13. Connect the 2 A/C compressor electrical connectors.
    • Attach the wiring harness retainer to the A/C tube stud bolt.
      G08028667
  14. Using a floor jack and a wooden block, support the engine.
    • Remove Engine Support Bar.
      G07978392
  15. Install the engine front cover. For additional information, refer to ENGINE FRONT COVER  .
  16. Install the oil level indicator.
    G08028664
  17. Fill the engine with clean engine oil.
scientia non olet · About LEMON Manuals