LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Taurus Limited, FWD >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> Fuel Charging System - Turbocharger >> Removal And Installation >> Turbocharger - RH >> Installation

Turbocharger - RH: Installation

  1. Install the oil supply tube filter, washer and bolt.
    1. Install the new oil supply tube filter in the oil supply tube block.
    2. Slide the new washer onto the oil supply tube block.
    3. Install the bolt into the oil supply tube block.
      Fig 1: Identifying Oil Supply Tube Filter, Washer And Bolt
      G06261424Courtesy of FORD MOTOR CO.
  2. Install the RH turbocharger oil supply tube.
    • Tighten the bolt to 35 Nm (26 lb-ft).
    3. NOTE: The upper RH turbocharger bracket bolts must be loosened in order to perform the tightening sequence or damage to the turbocharger may occur.
    Fig 2: Locating Upper RH Turbocharger-To-Cylinder Block Bracket Bolt
    G06261425Courtesy of FORD MOTOR CO.
  3. Loosen the 2 bolts for the upper RH turbocharger-to-cylinder block bracket.
  4. Install a new RH exhaust manifold-to-turbocharger gasket.
  5. Install the RH turbocharger assembly and the upper RH turbocharger-to-cylinder block bracket bolt.
    • Do not tighten the bolts at this time.
      Fig 3: Locating RH Exhaust Manifold To Turbocharger Gasket
      G06261426Courtesy of FORD MOTOR CO.
  6. Install the 3 new RH exhaust manifold-to-turbocharger bolts.
    • Tighten to 45 Nm (33 lb-ft).
      Fig 4: Locating RH Exhaust Manifold-To-Turbocharger Bolts
      G06261422Courtesy of FORD MOTOR CO.
  7. Install the RH engine lifting eye and the 2 bolts.
    • Tighten to 24 Nm (18 lb-ft).
  8. Install the 2 upper RH exhaust manifold heat shields and the 4 bolts.
    • Tighten to 14 Nm (124 lb-in).
      Fig 5: Locating Bolts And Upper RH Exhaust Manifold Heat Shields
      G06261421Courtesy of FORD MOTOR CO.
    9. NOTE: Align the index marks for the RH CAC tube.
  9. Install the RH CAC tube to the RH turbocharger and tighten the clamp.
    • To install, tighten to 5 Nm (44 lb-in).
      Fig 6: Locating Clamp And RH CAC Tube
      G06261420Courtesy of FORD MOTOR CO.
    10. NOTE: Align the index marks for the RH CAC tube.
  10. Install the RH CAC and tighten the clamp.
    • To install, tighten to 5 Nm (44 lb-in).
      Fig 7: Locating Clamp And RH CAC Tube
      G06261430Courtesy of FORD MOTOR CO.
  11. Install the RH CAC tube and the RH CAC tube nut to the intake manifold.
    • Tighten to 6 Nm (53 lb-in).
      Fig 8: Locating RH CAC Tube And RH CAC Tube Nut
      G06261431Courtesy of FORD MOTOR CO.
  12. Connect the RH turbocharger bypass valve hose.
    Fig 9: Locating RH Turbocharger Bypass Valve Hose
    G06261417Courtesy of FORD MOTOR CO.
  13. Connect the RH turbocharger bypass valve electrical connector.
    Fig 10: Locating RH Turbocharger Bypass Valve Electrical Connector
    G06261416Courtesy of FORD MOTOR CO.
  14. Install the turbocharger wastegate regulating valve hose to the RH CAC tube.
    Fig 11: Locating Turbocharger Wastegate Regulating Valve Hose
    G06261415Courtesy of FORD MOTOR CO.
  15. Connect the LH turbocharger bypass valve electrical connector and the turbocharger bypass valve hose.
    Fig 12: Locating LH Turbocharger Bypass Valve Electrical Connector And Turbocharger Bypass Valve Hose
    G06261414Courtesy of FORD MOTOR CO.
  16. Install the strut tower brace and the 4 nuts.
    • Tighten to 30 Nm (22 lb-ft).
  17. Attach the 2 brake booster vacuum hose retainers to the strut tower brace.
  18. Position the upper RH turbocharger-to-cylinder block bracket as far clockwise as possible and tighten the bolts in the following sequence.
    1. Tighten the lower cylinder block bracket bolt to 26 Nm (19 lb-ft).
    2. Tighten the upper cylinder block bracket bolt to 26 Nm (19 lb-ft).
    3. Tighten the cylinder block bracket-to-turbocharger bolt to 19 Nm (168 lb-in).
      Fig 13: Identifying Upper RH Turbocharger-To-Cylinder Block Bracket And Bolts Tightening Sequence
      G06282276Courtesy of FORD MOTOR CO.
  19. Using 2 new sealing washers, install the 2 RH turbocharger coolant tube banjo bolts.
    • Tighten to 40 Nm (30 lb-ft).
      Fig 14: Locating Coolant Tube Banjo Bolts And RH Turbocharger Coolant Tubes
      G06261413Courtesy of FORD MOTOR CO.
    20. NOTE: Lubricate the cylinder block bore with clean engine oil.
    Fig 15: Locating O-Ring Seals And RH Turbocharger Oil Return Tube
    G06261412Courtesy of FORD MOTOR CO.
  20. Using 2 new O-ring seals, install the RH turbocharger oil return tube in the cylinder block.
  21. Install a new gasket and install the RH turbocharger oil return tube and the 2 bolts.
    • Tighten to 10 Nm (89 lb-in).
      Fig 16: Locating RH Turbocharger Oil Return Tube And Bolts
      G06261411Courtesy of FORD MOTOR CO.
  22. Install the lower RH turbocharger bracket and the 3 bolts and tighten in sequence shown in illustration.
    1. Tighten the lower RH turbocharger bracket-to-turbocharger bolt to 19 Nm (168 lb-in).
    2. Tighten the 2 lower RH turbocharger bracket-to-cylinder block bolts to 48 Nm (35 lb-in).
      Fig 17: Identifying Lower RH Turbocharger Bracket And Bolts Tightening Sequence
      G06261440Courtesy of FORD MOTOR CO.
    23. NOTE: Make sure the turbocharger wastegate regulating valve hose does not contact the exhaust manifold heat shield.
    Fig 18: Locating Turbocharger Wastegate Regulating Valve Hose Clamp
    G06282049Courtesy of FORD MOTOR CO.
  23. Connect the turbocharger wastegate regulating valve hose to the RH turbocharger.
    24. NOTE: Align the index marks for the RH turbocharger intake pipe.
  24. Install the RH turbocharger intake pipe to the RH turbocharger and tighten the clamp.
    • To install, tighten to 5 Nm (44 lb-in).
      Fig 19: Locating RH Turbocharger Intake Pipe Clamp
      G06261408Courtesy of FORD MOTOR CO.
  25. Install the lower RH exhaust manifold heat shield bolt.
    • Tighten to 14 Nm (124 lb-in).
      Fig 20: Locating Lower RH Exhaust Manifold Heat Shield Bolt
      G06261443Courtesy of FORD MOTOR CO.
    26. NOTE: Listen for audible click when installing the oil supply tube into the quick connect fitting.
    Fig 21: Locating RH Turbocharger Oil Supply Tube With Quick Connect Fitting
    G06261444Courtesy of FORD MOTOR CO.
  26. Install the RH turbocharger oil supply tube into the quick connect fitting.
  27. Install the RH turbocharger oil supply tube secondary latch.
    Fig 22: Locating RH Turbocharger Oil Supply Tube Secondary Latch
    G06261405Courtesy of FORD MOTOR CO.
  28. Install the front subframe. For additional information, refer to UNI-BODY, SUBFRAME AND MOUNTING SYSTEM .
  29. Install the RH catalytic converter. For additional information, refer to EXHAUST SYSTEM .
  30. Fill and bleed the cooling system. For additional information, refer to ENGINE COOLING .
  31. Install the underbody shield and the 4 retainers.
    Fig 23: Locating Retainers And Underbody Shield
    G06261404Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals