LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Mustang Base, 2D Coupe, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 89 (Fuel Charging System - Turbocharger -- F250-F550 Super Duty) >> Removal And Installation >> Turbocharger >> Removal

Removal And Installation: Turbocharger: Removal

WARNING: This page is about a different car, the 2012 Ford Pickup, 2012 Ford F550 Super Duty, 2012 Ford F450 Super Duty, and 2012 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath the turbocharger are direct passages to the lubrication system. Debris and or coolant may enter lubrication system and engine damage may occur.
  1. Disconnect the battery ground cable. For additional information, refer to BATTERY, MOUNTING AND CABLES .
  2. Drain the primary engine cooling system. For additional information, refer to ENGINE COOLING - DIESEL ENGINE .
  3. Remove the lower intake manifold. For additional information, refer to ENGINE - 6.7L DIESEL .
  4. Disconnect the heater core inlet hose from the heater inlet tube.
  5. Remove 2 bolts and the heater core inlet tube.
    • Inspect O-ring seal for damage, replace if necessary.
  6. Disconnect the turbocharger actuator electrical connector.
  7. If equipped, disconnect the turbocharger wastegate actuator vacuum hose.
    8. NOTE: Mark the position of the exhaust upper downpipe clamp for installation.
    Fig 1: Locating Exhaust Upper Downpipe Clamp
    G07481792Courtesy of FORD MOTOR CO.
  8. Loosen the exhaust upper downpipe clamp.
  9. Remove the RH fender splash shield. For additional information, refer to FRONT END BODY PANELS .
  10. Remove the exhaust upper downpipe bracket bolt.
    Fig 2: Locating Exhaust Upper Downpipe Bracket Bolt
    G07481793Courtesy of FORD MOTOR CO.
  11. Remove the 2 exhaust lower downpipe-to-catalyst and particulate filter assembly bolts and remove the downpipe assembly.
    • Discard the exhaust upper downpipe clamp.
      Fig 3: Locating Exhaust Lower Downpipe-To-Catalyst And Particulate Filter Assembly Bolts
      G07481794Courtesy of FORD MOTOR CO.
  12. Loosen the RH turbocharger inlet pipe clamp and slide the clamp off the turbocharger.
    • Discard the clamp after turbocharger is removed.
  13. Loosen the LH turbocharger inlet pipe clamp and slide the clamp off the turbocharger.
    • Discard the clamp after turbocharger is removed.
    14. NOTE: Use a 3/8 inch Jiffy-tite quick line disconnect tool, such as Snap-on® LDTSP4 or equivalent, to disconnect the turbocharger coolant outlet tube.
    NOTE: If necessary, remove the turbocharger heat shield and discard the bolts.
    Fig 4: Locating Turbocharger Coolant Outlet Tube
    G07481795Courtesy of FORD MOTOR CO.
  14. Disconnect the turbocharger coolant outlet tube from the turbocharger.
    15. NOTE: Lift the turbocharger off locating dowels before positioning forward for removal.
    NOTE: The turbocharger is a tight fit between cowl and injection pump fuel lines but comes out without removing fuel lines.
  15. Remove the 4 bolts and the turbocharger.
    • Discard the turbocharger gasket and bolts.
    16. NOTE: Use a 3/8 inch Jiffy-tite quick line disconnect tool, such as Snap-on® LDTSP4 or equivalent.
  16. Disconnect the turbocharger coolant outlet tube at the center housing and secure tube off to the side.
    17. NOTE: Use a 3/8 inch Jiffy-tite quick line disconnect tool, such as Snap-on® LDTSP4 or equivalent.
  17. If servicing or replacing the turbocharger, disconnect the turbocharger oil supply tube from the turbocharger oil supply fittings.
    • Discard the oil supply tube.
  18. Inspect the turbocharger coolant outlet tube fitting at the center housing of the turbocharger and replace, as necessary.
scientia non olet · About LEMON Manuals