Transfer Case Front Output Shaft Seal - (Vehicles With: 2-Speed Torque On Demand Transfer Case): Installation

WARNING: This page is about a different car, the 2015 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

1.

Using the special tools, install the front output shaft bearing.
Use Special Service Tool: 205-153 (T80T-4000-W) Handle, 205-293 (T89P-4850-A) Installer, Differential Oil Seal.

Courtesy of FORD MOTOR COMPANY

2.

Using the special tool, install the front output shaft seal.
Use Special Service Tool: 308-250 (T96T-7127-B) Installer, Output Shaft Oil Seal.

Courtesy of FORD MOTOR COMPANY

3.

NOTE: Do not let the front output shaft fall while removing the snap ring or damage to the component may occur.

Install the output shaft and the out put shaft circlip.

Courtesy of FORD MOTOR COMPANY

4.

Install the output shaft sprocket spacer.

Courtesy of FORD MOTOR COMPANY

5.

Install the drive chain and the sprockets as an assembly.

Courtesy of FORD MOTOR COMPANY

6.

NOTE: When installing the clutch assembly, do not separate the clutch pack assembly. The thrust washer in the lower clutch pack uses tabs to hold it in place. If the thrust washer is not in place, a transfer case clearance problem will occur.

NOTE: If the clutch pack is disassembled, a new clutch pack and armature must be installed. Failure to install a new clutch pack can result in component failure.

Install the clutch pack assembly with the armature.

Courtesy of FORD MOTOR COMPANY

7.

Install the clutch pack circlip.

Courtesy of FORD MOTOR COMPANY

8.

Install the wave spring.

Courtesy of FORD MOTOR COMPANY

9.

Install the cam and the steel balls.

Courtesy of FORD MOTOR COMPANY

10.

Install the coil housing.

Courtesy of FORD MOTOR COMPANY

11.

Install the coil housing thrust bearing assembly.

Courtesy of FORD MOTOR COMPANY

12.

Install the coil housing snap ring.

Courtesy of FORD MOTOR COMPANY

13.

Install the transfer case field coil.

Courtesy of FORD MOTOR COMPANY

14.

NOTE: Only apply enough silicone sealant to seal the transfer case halves together.

Apply a small bead of silicone sealant to the mating surface of the case half.

Material

: Ultra Silicone Sealant / TA-29

Courtesy of FORD MOTOR COMPANY

15.

NOTE: Position the field coil bolts to align with the field coil bolt holes in the rear case. Position field coil wire through the field coil wire through hole in the case.

Position the transfer case halves and tighten the bolts in the sequence shown in illustration.

Torque

: 21 lb.ft (29 Nm)

Courtesy of FORD MOTOR COMPANY

16.

Install the coil washers and nuts.
Torque

: 89 lb.in (10 Nm)

Courtesy of FORD MOTOR COMPANY

17.

Install the transfer case rear seal. Refer to: Transfer Case Rear Seal .

18.

Apply a small bead of silicone sealant to the transfer case shift motor mating surface.
Material

: Ultra Silicone Sealant / TA-29

Courtesy of FORD MOTOR COMPANY

19.

NOTE: When installing the shift motor, tighten the bracket nuts last. Failure to follow the steps in the correct order may result in damage to the component.
- 1.
  
  Install the transfer case shift motor.
- 2.
  
  Install the transfer case shift motor bolts.
  Torque
  
  : 89 lb.in (10 Nm)
- 3.
  
  Install the transfer case shift motor bracket bolt.
  Torque
  
  : 89 lb.in (10 Nm)
- 4.
  
  Tighten the transfer case shift motor bracket nuts.
  Torque
  
  : 27 lb.in (3 Nm)

Courtesy of FORD MOTOR COMPANY

20.

NOTE: After the coil wire is inserted into the connector, gently pull the wire back to verify the pin is locked inside the connector.

Install the coil wire pin in the electrical connector.
- 1.
  
  Insert the coil wire pin in the electrical connector.
- 2.
  
  Install the inner connector retainer.

Courtesy of FORD MOTOR COMPANY

21.

Remove the transfer case from the transmission adjustable mounting arms.
Use the General Equipment: Adjustable Mounting Arm

Courtesy of FORD MOTOR COMPANY

22.

Install the transfer case. Refer to: Transfer Case .