Engine Mount RH: Installation

4x2/4x4 

1. 1.
   
   
   NOTE: If a new engine mount is installed, remove the 2 studs prior to positioning the assembly in the vehicle.

   Install the engine mount and the new bolts.

   Torque

   : 57 lb.ft (77 Nm)

Courtesy of FORD MOTOR COMPANY

1. 2.
   
   

   1. 1.
      
      Using the adjustable stand, lower the engine to the installed position. Use the General Equipment: Vehicle/Axle Stands

   1. 2.
      
      Remove the stand.

Courtesy of FORD MOTOR COMPANY

1. 3.
   
   
   NOTE: Only use hand tools when installing the engine mount studs or damage to the engine mount can occur.

   Install the engine mount studs.

   Torque

   : 22 lb.ft (30 Nm)

Courtesy of FORD MOTOR COMPANY

1. 4.
   
   
   NOTE: Only use hand tools when installing the engine mount nuts or damage to the engine mount can occur.

   Install the new engine mount nuts.

   Torque

   : 111 lb.ft (150 Nm)

Courtesy of FORD MOTOR COMPANY

1. 5.
   
   
   NOTE: Only use hand tools when tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

   Install the new LH engine mount through bolt.

   Torque

   : 258 lb.ft (350 Nm)

Courtesy of FORD MOTOR COMPANY

4x2 

1. 6.
   
   Position the stabilizer bar and install the new nuts.

   Torque

   : 41 lb.ft (55 Nm)

Courtesy of FORD MOTOR COMPANY

4x4 

1. 7.
   
   Install the front drive shaft. Refer to: Front Driveshaft .

4x2/4x4 

1. 8.
   
   
   NOTE: Only use hand tools when installing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

   Tighten the transmission mount-to-crossmember nuts.

   Torque

   : 85 lb.ft (115 Nm)

Courtesy of FORD MOTOR COMPANY

1. 9.
   
   
   • Position the exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe and install the new bolts.
   • Tighten the inner exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

     Torque

     : 46 lb.ft (63 Nm)

   • Tighten the outer exhaust Y-pipe dual catalytic converter-to-exhaust intermediate pipe bolt.

     Torque

     : 46 lb.ft (63 Nm)

Courtesy of FORD MOTOR COMPANY

1. 10.
   
   Position the A/C compressor and install the bolts.

   Torque

   : 18 lb.ft (25 Nm)

Courtesy of FORD MOTOR COMPANY

1. 11.
   
   Install the following items:
   • RH fender splash shield. Refer to: Fender Splash Shield .
   • RH wheel and tire. Refer to: Wheel and Tire .

1. 12.
   
   

   1. 1.
      
      Install the pin-type retainer.

   1. 2.
      
      Install the ground wire and bolt.

      Torque

      : 18 lb.ft (25 Nm)

Courtesy of FORD MOTOR COMPANY

1. 13.
   
   Install the following items:
   • Refer to: ACCESSORY DRIVE BELT
   • Refer to: STARTING SYSTEM .

1. 14.
   
   If equipped, install the skid plate and bolts.

   Torque

   : 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

1. 15.
   
   If equipped, install the underbody shield and fasteners.

   Torque

   : 71 lb.in (8 Nm)

Courtesy of FORD MOTOR COMPANY

1. 16.
   
   If equipped, install the underbody shield and fasteners.

   Torque

   : 30 lb.ft (40 Nm)

Courtesy of FORD MOTOR COMPANY

1. 17.
   
   Install the following items:
   • Refer to: CHARGE AIR COOLER (CAC) OUTLET PIPE .
   • RH CAC intake pipe. Refer to: CHARGE AIR COOLER (CAC) INTAKE PIPE
   • Refer to: AIR CLEANER OUTLET PIPE LH
   • Refer to: AIR CLEANER OUTLET PIPE RH .

1. 18.
   
   Connect the battery ground cable. Refer to: Battery Disconnect and Connect .

1. 19.
   
   Check the exhaust system for leaks.