Instrument Panel Cluster (IPC) DTC Chart

WARNING: This page is about a different car, the 2014 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

DTC	Description	Action
B1A82:11	External Trip Switch: Circuit Short To Ground	GO to PINPOINT TEST AF .
B1A82:13	External Trip Switch: Circuit Open	GO to PINPOINT TEST AF .
B1A82:23	External Trip Switch: Signal Stuck Low	INSTALL a new LH steering wheel switch. REFER to STEERING WHEEL SWITCH . CLEAR the DTCs. REPEAT the self-test.
P0460:11	Fuel Level Sensor A Circuit: Circuit Short to Ground	GO to PINPOINT TEST B .
P0460:13	Fuel Level Sensor A Circuit: Circuit Open	GO to PINPOINT TEST B .
P062F:46 Internal	Control Module EEPROM Error: Calibration/Parameter Memory Failure	CLEAR the DTCs. REPEAT the self-test. If DTC P062F:46 returns, INSTALL a new IPC . REFER to Instrument Panel Cluster (IPC) . TEST the system for normal operation.
P1534:01	Restraint Deployment Indicator Circuit: General Electrical Failure	INSTALL a new IPC . REFER to Instrument Panel Cluster (IPC) . TEST the system for normal operation.
P1706:00	High Vehicle Speed Observed in Park: No Sub Type Information	GO to PINPOINT TEST X .
U0100:00	Lost Communication With ECM /PCM "A": No Sub-Type Information	GO to PINPOINT TEST AT .
U0102:00	Lost Communication With Transfer Case Control Module: No Sub-Type Information	GO to PINPOINT TEST AU .
U0121:00	Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub-Type Information	GO to PINPOINT TEST AV .
U0131:00	Lost Communication With Power Steering Control Module: No Sub-Type Information	GO to PINPOINT TEST AW .
U0137:00	Lost Communication With Trailer Brake Control Module: No Sub-Type Information	GO to PINPOINT TEST AX .
U0140:00	Lost Communication With Body Control Module: No Sub-Type Information	GO to PINPOINT TEST AY .
U0151:00	Lost Communication With Restraints Control Module: No Sub-Type Information	GO to PINPOINT TEST AZ .
U0154:00	Lost Communication With Restraints Occupant Classification System Module: No Sub-Type Information	GO to PINPOINT TEST BA .
U0159:00	Lost Communication With Parking Assist Control Module "A": No Sub-Type Information	GO to PINPOINT TEST BB .
U0212:00	Lost Communication With Steering Column Control Module: No Sub-Type Information	GO to PINPOINT TEST BC .
U0401:00	Invalid Data Received from ECM /PCM A: No Sub-Type Information	This DTC sets when the IPC receives invalid network data from the PCM for the vehicle speed input. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for the correct navigation of all DTCs. TEST the system for normal operation.
U0401:55	Invalid Data Received from ECM /PCM A: Not Configured	This DTC sets when the IPC receives invalid network data from the PCM for Trailer Brake Control (TBC) when the IPC is not configured for TBC . CARRY OUT the Programmable Module Installation (PMI) (when the original module is not available) for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation.
U0401:81	Invalid Data Received from ECM /PCM A: Invalid Serial Data Received	This DTC sets when the IPC receives invalid network data from the PCM for the engine temperature data. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for the correct navigation of all DTCs. TEST the system for normal operation.
U0401:86	Invalid Data Received from ECM /PCM A: Signal Invalid	This DTC sets when the IPC receives invalid network data from the PCM for the odometer data. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES for the correct navigation of all DTCs. TEST the system for normal operation.
U0415:56	Invalid Data Received from Anti-Lock Brake System (ABS) Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid data from the ABS module. DETERMINE which module (IPC or ABS module) has been replaced. CARRY OUT the Programmable Module Installation (PMI) (when the original module is not available) for the module in question. REFER to MODULE CONFIGURATION . TEST the system for normal operation.
U0422:00	Invalid Data Received from Body Control Module: No Sub-Type Information	This DTC sets when the IPC receives invalid Body Control Module (BCM) data for the Tire Pressure Monitoring System (TPMS) function. RETRIEVE and REPAIR all non-network DTCs in the BCM . REFER to MULTIFUNCTION ELECTRONIC MODULES for the correct navigation of all DTCs. TEST the system for normal operation.
U0422:56	Invalid Data Received from Body Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives BCM data for the autolamp function and the IPC is not configured for autolamps. DETERMINE which module (IPC or BCM ) has been replaced. CARRY OUT the Programmable Module Installation (PMI) (when the original module is not available) for the module in question. REFER to MODULE CONFIGURATION . TEST the system for normal operation.
U045A:55	Invalid Data Received From Parking Assist Control Module "A": Not Configured	This DTC sets when the IPC receives rear parking aid data when the IPC is not configured for parking aid. CARRY OUT the PMI (when the original module is not available) for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation.
U045A:68	Invalid Data Received From Parking Assist Control Module "A": Event Information	This DTC sets when the IPC receives invalid rear parking aid data. RETRIEVE and REPAIR all non-network DTCs in the Parking Aid Module (PAM). REFER to PARKING AID for a list of all DTCs. If there are no DTCs present, INSTALL a new PAM . REFER to PARKING AID . TEST the system for normal operation.
U0462:82	Invalid Data Received from Compass Module: Alive/Sequence Counter Incorrect/Not Updated	If equipped with a 4.2" message center and a 4.2" FCDIM , GO to PINPOINT TEST AG . For all other configurations, Refer to the appropriate article for the procedure.
U0545:56	Invalid Data Received From Running Board Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives Power Running Board (PRB) data when the IPC is not configured for PRB s. CARRY OUT the PMI (when the original module is not available) for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation.
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CARRY OUT the PMI (when the original module is not available) for the IPC . REFER to MODULE CONFIGURATION . TEST the system for normal operation. After the PMI , CLEAR the DTC. REPEAT the self-test.
U3000:04	Control Module: System Internal Failure	CLEAR the DTCs. REPEAT the self-test. If the DTC returns, INSTALL a new IPC . REFER to Instrument Panel Cluster (IPC) . TEST the system for normal operation.
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST BD .
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST BE .
U300A:64	Ignition Switch: Signal Plausibility Failure	This DTC sets on-demand and in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. REFER to STEERING COLUMN SWITCHES to diagnose the ignition start circuit to the BCM .