LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Mustang Base, 2D Coupe, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 369 (Supplemental Restraint System) >> Diagnosis And Testing >> Airbag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Tests >> Pinpoint Test J: DTCs B0091:11, B0091:93, B0097:11 and B0097:93 >> PINPOINT TEST J: DTCs B0091:11, B0091:93, B0097:11 AND B0097:93

PINPOINT TEST J: DTCs B0091:11, B0091:93, B0097:11 AND B0097:93

WARNING: This page is about a different car, the 2013 Ford F-550 Super Duty, 2013 Ford F-450 Super Duty, 2013 Ford F-350 Super Duty, and 2013 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy and cause serious personal injury or death.
NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough INSPECTION AND VERIFICATION  before proceeding with the pinpoint test.
NOTE: SRS components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE: Do not probe any impact sensor. The impact sensor cannot be tested using a multi-meter.
  1. J1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Were any DTCs retrieved on-demand during self-test? 
    • Yes  : Fault(s) cannot be cleared until corrected and the DTC(s) are no longer retrieved on-demand during self-test.

      SuperCab and Crew Cab vehicles: 

      For DTC B0091:11 AND  B0097:11, GO to J2.

      For DTC B0091:93 AND  B0097:93, GO to  J6.

      For DTC B0091:93 ONLY  , GO to  J8.

      For DTC B0097:93 ONLY  , GO to  J11.

      Regular cab vehicles: 

      For DTC B0091:11, GO to J2.

      For DTC B0091:93, GO to  J8.

    • No  : The fault is intermittent when present as a CMDTC only. GO to  J15.
  2. J2 CHECK THE LEFT SIDE RESTRAINTS SENSOR 1 DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Front Door Side Impact Sensor C567.
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • DIAGNOSTIC TIP:  When viewing DTCs with the driver front door side impact sensor disconnected, an open circuit (no operation) fault would normally be retrieved.
    • For SuperCab and Crew Cab vehicles, did the on-demand DTCs change from B0091:11 and B0097:11 to B0091:93? 

      For regular cab vehicles, did the on-demand DTC change from B0091:11 to B0091:93? 

    • Yes  : INSTALL a new driver front door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . GO to  J16.
    • No  : For SuperCab and Crew Cab vehicles, GO to J3. For regular cab vehicles, GO to  J4.
  3. J3 CHECK THE RIGHT SIDE RESTRAINTS SENSOR 2 DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Connect: Driver Front Door Side Impact Sensor C567.
    • Disconnect: Passenger Second Row Side Impact Sensor C3249.
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger second row side impact sensor disconnected, an open circuit (no operation) fault would normally be retrieved.
    • Did the on-demand DTC change from B0091:11 and B0097:11 to B0097:93? 
  4. J4 CHECK THE DRIVER FRONT DOOR SIDE IMPACT SENSOR FEED CIRCUIT FOR A SHORT TO GROUND AND SHORT BETWEEN SENSOR CIRCUITS 
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Driver Front Door Side Impact Sensor C567 (if not previously disconnected).
    • Disconnect: RCM C310A and C310B.
    • Measure the resistance between driver front door side impact sensor:
      • C567-1, circuit VR217 (GY/YE), harness side and ground.
      • C567-1, circuit VR217 (GY/YE), harness side and C567-2, circuit RR131 (VT/GY), harness side.
        Fig 1: Measuring Resistance Between Driver Front Door Side Impact Sensor C567-1, Circuit VR217 (GY/YE) And Ground
        G07975719Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10, 000 ohms? 
    • Yes  : For SuperCab and Crew Cab vehicles, GO to J5.

      For regular cab vehicles, GO to  J14.

    • No  : REPAIR circuit VR217 (GY/YE) and/or RR131 (VT/GY). GO to  J16.
  5. J5 CHECK THE PASSENGER SECOND ROW SIDE IMPACT SENSOR FEED CIRCUIT FOR A SHORT TO GROUND AND SHORT BETWEEN SENSOR CIRCUITS 
    • Measure the resistance between passenger second row side impact sensor:
      • C3249-1, circuit VR220 (VT/OG), harness side and ground.
      • C3249-1, circuit VR220 (VT/OG), harness side and C3249-2, circuit RR134 (BN/BU), harness side.
        Fig 2: Checking Passenger Second Row C-Pillar Side Impact Sensor Feed Circuit For Short To Ground And Short Between Sensor Circuits
        G06255036Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10, 000 ohms? 
    • Yes  : GO to  J14.
    • No  : REPAIR circuit VR220 (VT/OG) and/or RR134 (BN/BU). GO to  J16.
  6. J6 CHECK THE DRIVER FRONT DOOR SIDE IMPACT SENSOR CIRCUITS FOR A SHORT TO VOLTAGE (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310A and C310B (if not previously disconnected).
    • Disconnect: Driver Front Door Side Impact Sensor C567 (if not previously disconnected).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Measure the voltage between driver front door side impact sensor:
      • C567-1, circuit VR217 (GY/YE), harness side and ground.
      • C567-2, circuit RR131 (VT/GY), harness side and ground.
        Fig 3: Checking Driver Front Door Side Impact Sensor Circuits For Short To Voltage (No Operation Indicated)
        G06134898Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes  : REPAIR circuit VR217 (GY/YE) or RR131 (VT/GY). GO to  J16.
    • No  : For SuperCab and Crew Cab vehicles, GO to J7.

      For regular cab vehicles, GO to  J9.

  7. J7 CHECK THE PASSENGER SECOND ROW SIDE IMPACT SENSOR CIRCUITS FOR A SHORT TO VOLTAGE (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Disconnect: Passenger Second Row Side Impact Sensor C3249.
    • Ignition ON.
    • Measure the voltage between passenger second row side impact sensor:
      • C3249-1, circuit VR220 (VT/OG), harness side and ground.
      • C3249-2, circuit RR134 (BN/BU), harness side and ground.
        Fig 4: Checking Passenger Second Row Side Impact Sensor Circuits For Short To Voltage (No Operation Indicated)
        G06063751Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes  : REPAIR circuit VR220 (VT/OG) or RR134 (BN/BU). GO to  J16.
    • No  : GO to  J14.
  8. J8 CHECK THE DRIVER FRONT DOOR SIDE IMPACT SENSOR AND RCM CONNECTIONS (NO OPERATION INDICATED) 
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Gain access to the driver front door side impact sensor and inspect C567 to be fully seated and locked. Seat and lock the connector as necessary. Refer to SIDE IMPACT SENSOR - FRONT DOOR .
    • Gain access to the RCM and inspect C310A and C310B to be fully seated and locked. Seat and lock the connector(s) as necessary. Refer to RESTRAINTS CONTROL MODULE (RCM) .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Was DTC B0091:93 retrieved on-demand during self-test? 
    • Yes  : For SuperCab and Crew Cab vehicles, GO to J9.

      For regular cab vehicles, GO to  J6.

    • No  : The fault has been corrected. GO to  J16.
  9. J9 CHECK THE DRIVER FRONT DOOR SIDE IMPACT SENSOR CIRCUITS FOR AN OPEN (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310A and C310B (if not previously disconnected).
    • Disconnect: Driver Front Door Side Impact Sensor C567 (if not previously disconnected).
    • Measure the resistance between RCM C310B, harness side and driver front door side impact sensor C567, harness side using the following chart.
      RCM Circuit Driver Front Door Side Impact Sensor
      C310B-36 VR217 (GY/YE) C567-1
      C310B-35 RR131 (VT/GY) C567-2
      Fig 5: Checking Driver Front Door Side Impact Sensor Circuits For Open (No Operation Indicated)
      G06174029Courtesy of FORD MOTOR CO.
    • Are the resistances less than 0.5 ohm? 
    • Yes  : GO to J10.
    • No  : REPAIR circuit VR217 (GY/YE) or RR131 (VT/GY). GO to  J16.
  10. J10 CHECK THE LEFT SIDE RESTRAINTS SENSOR 1 DTC FOR A FAULT STATUS CHANGE (NO OPERATION INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Connect: RCM C310A and C310B.
    • Connect a fused jumper wire between driver front door side impact sensor C567-1, circuit VR217 (GY/YE), harness side and driver front door side impact sensor C567-2, circuit RR131 (VT/GY), harness side.
      Fig 6: Connecting Fused Jumper Wire Between Driver Front Door Side Impact Sensor C567-1, Circuit VR217 (GY/YE) And C567-2, Circuit RR131 (VT/GY)
      G06509051Courtesy of FORD MOTOR CO.
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • DIAGNOSTIC TIP:  When viewing DTCs with the driver front door side impact sensor circuits shorted together, a short to ground fault would normally be retrieved.
    • For SuperCab and Crew Cab vehicles, did the DTC change from B0091:93 to B0091:11 and B0097:11? 

      For regular cab vehicles, did the DTC change from B0091:93 to B0091:11? 

    • Yes  : REMOVE the fused jumper wire and INSTALL a new driver front door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . GO to  J16.
    • No  : REMOVE the fused jumper wire and GO to  J14.
  11. J11 CHECK THE PASSENGER SECOND ROW SIDE IMPACT SENSOR AND RCM CONNECTIONS (NO OPERATION INDICATED) 
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Gain access to the passenger second row side impact sensor and inspect C3249 to be fully seated and locked. Seat and lock the connector as necessary. Refer to SIDE IMPACT SENSOR - SECOND ROW, SUPERCAB  or SIDE IMPACT SENSOR - SECOND ROW, CREW CAB .
    • Gain access to the RCM and inspect C310A and C310B to be fully seated and locked. Seat and lock the connector(s) as necessary. Refer to RESTRAINTS CONTROL MODULE (RCM) .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Was DTC B0097:93 retrieved on-demand during self-test? 
    • Yes  : GO to J12.
    • No  : The fault has been corrected. GO to  J16.
  12. J12 CHECK THE PASSENGER SECOND ROW SIDE IMPACT SENSOR CIRCUITS FOR AN OPEN (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM C310A and C310B.
    • Disconnect: Passenger Second Row Side Impact Sensor C3249.
    • Measure the resistance between RCM C310B, harness side and passenger second row side impact sensor C3249, harness side using the following chart.
      RCM Circuit Passenger Second Row Side Impact Sensor
      C310B-37 VR220 (VT/OG) C3249-1
      C310B-38 RR134 (BN/BU) C3249-2
      Fig 7: Checking Passenger Second Row Side Impact Sensor Circuits For Open (No Operation Indicated)
      G06100077Courtesy of FORD MOTOR CO.
    • Are the resistances less than 0.5 ohm? 
    • Yes  : GO to J13.
    • No  : REPAIR circuit VR220 (VT/OG) or RR134 (BN/BU). GO to  J16.
  13. J13 CHECK THE RIGHT SIDE RESTRAINTS SENSOR 2 DTC FOR A FAULT STATUS CHANGE (NO OPERATION INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Connect: RCM C310A and C310B.
    • Connect a fused jumper wire between passenger second row side impact sensor C3249-1, circuit VR220 (VT/OG), harness side and passenger second row side impact sensor C3249-2, circuit RR134 (BN/BU), harness side.
      Fig 8: Connecting Fused Jumper Wire Between Passenger Second Row Side Impact Sensor C3249-1, Circuit VR220 (VT/OG) And C3249-2, Circuit RR134 (BN/BU)
      G06509046Courtesy of FORD MOTOR CO.
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger second row side impact sensor circuits shorted together, a short to ground fault would normally be retrieved.
    • Did the DTC change from B0097:93 to B0097:11 and B0091:11? 
  14. J14 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system components and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found. Refer to "OEM Connector Repair Procedures" Article for schematic and connector information.
    • Connect: RCM C310A and C310B.
    • Connect: Driver Front Door Side Impact Sensor C567 (if previously disconnected).
    • Connect: Passenger Second Row Side Impact Sensor C3249 (if previously disconnected).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Was the original DTC retrieved on-demand during self-test? 
    • Yes  : INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  J16.
    • No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test  . GO to J15.
  15. J15 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: Affected Impact Sensor Driver Front Door Side Impact Sensor C567 and/or Passenger Second Row Side Impact Sensor C3249 (if equipped).
    • Disconnect: RCM C310A and C310B.
    • Inspect for the following:
      • inspect harness and component connectors for loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found. Refer to "OEM Connector Repair Procedures" Article for schematic and connector information.
    • Connect: All Previously Disconnected Component(s)/Connector(s).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Was DTC B0091:11, B0091:93, B0097:11 or B0097:93 retrieved on-demand during self-test? 
    • Yes  : Fault(s) cannot be cleared until corrected and the DTC(s) are no longer retrieved on-demand during self-test.

      SuperCab and Crew Cab vehicles: 

      For DTC B0091:11 AND  B0097:11, GO to  J2.

      For DTC B0091:93 AND  B0097:93, GO to  J6.

      For DTC B0091:93 ONLY  , GO to  J8.

      For DTC B0097:93 ONLY  , GO to  J11.

      Regular cab vehicles: 

      For DTC B0091:11, GO to  J2.

      For DTC B0091:93, GO to  J8.

    • No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test  . GO to J16.
  16. J16 CHECK FOR ADDITIONAL SRS DTCs 
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Reconnect all SRS components (if previously disconnected).
    • If previously directed to depower the SRS, repower the SRS. Do not  prove out the SRS at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Are any RCM DTCs retrieved on-demand during self-test? 
    • Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the DTC CHARTS  for pinpoint test direction.
    • No  : CLEAR all RCM CMDTCs. PROVE OUT the SRS. Repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals