Crankshaft Rear Seal with Retainer Plate: Removal

WARNING: This page is about a different car, the 2013 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces that enters the oil passages, coolant passages or the oil pan, can cause engine failure.

NOTE: The engine is equipped with a cast aluminum (early build) or stamped steel (late build) crankshaft rear seal retainer plate. If the engine is equipped with a stamped steel retainer plate, the seal and plate must be removed as an assembly and discarded.

NOTE: This procedure is for removal of the crankshaft rear seal and retainer plate. If only removing the crankshaft rear seal, refer to CRANKSHAFT REAR SEAL .

ll crankshaft rear seal retainer plates

With the vehicle in NEUTRAL, position it on a hoist. Refer to JACKING & LIFTING .
Remove the flexplate. Refer to FLEXPLATE .
NOTE: The engine can be equipped with a cast aluminum (early build) or stamped steel (late build) crankshaft rear seal retainer plate.

NOTE: Cast aluminum crankshaft rear seal retainer plate shown in illustration, stamped steel crankshaft rear seal retainer plate similar.

Remove the crankshaft sensor ring.

Fig 1: Identifying Crankshaft Sensor Ring
Courtesy of FORD MOTOR CO.
Remove the engine-to-transmission spacer plate.
If equipped, remove the 2 bolts and the exhaust system heat shield.

Fig 2: Locating Exhaust System Heat Shield And Bolts
Courtesy of FORD MOTOR CO.
NOTE: The Crankshaft Position (CKP) heat shield is only positioned aside.

Remove the nut and the bolt. Position the Crankshaft Position (CKP) heat shield aside.

Fig 3: Locating Crankshaft Position Heat Shield, Bolt And Nut
Courtesy of FORD MOTOR CO.
Remove the wiring harness grommet.

Fig 4: Locating Wiring Harness Grommet
Courtesy of FORD MOTOR CO.
Disconnect the CKP sensor electrical connector.

Fig 5: Locating Crankshaft Position (CKP) Sensor Electrical Connector
Courtesy of FORD MOTOR CO.
Remove the bolt and the CKP sensor.

Fig 6: Locating CKP Sensor And Bolt
Courtesy of FORD MOTOR CO.
If equipped, remove the 4 bolts and the skid plate.
Remove the 2 oil pan-to-crankshaft rear seal retainer plate bolts.

Fig 7: Locating Oil Pan-To-Crankshaft Rear Seal Retainer Plate Bolts
Courtesy of FORD MOTOR CO.

Cast aluminum (early build) crankshaft rear seal retainer plate
Using the Crankshaft Rear Oil Seal Remover and Slide Hammer, remove and discard the crankshaft rear seal.

Fig 8: Removing Rear Crankshaft Seal Using Crankshaft Rear Oil Seal Remover And Slide Hammer
Courtesy of FORD MOTOR CO.
Remove the 8 crankshaft rear seal retainer bolts.

Fig 9: Locating Crankshaft Rear Seal Retainer Bolts
Courtesy of FORD MOTOR CO.
Install the 2 M6 oil pan bolts (finger-tight) into the 2 threaded holes in the crankshaft rear seal retainer.
- Alternately tighten the 2 bolts one turn at a time until the crankshaft rear seal retainer-to-cylinder block seal is released.
  - Remove the crankshaft rear seal retainer.
    
    Fig 10: Locating Crankshaft Rear Seal Retainer Mounting Bolts
    Courtesy of FORD MOTOR CO.
Stamped steel (late build) crankshaft rear seal retainer plate
Remove the 8 bolts and the crankshaft rear seal retainer.
- Discard the crankshaft rear seal retainer.
  
  Fig 11: Locating Crankshaft Rear Seal Retainer Bolts
  Courtesy of FORD MOTOR CO.
All crankshaft rear seal retainer plates
NOTE: Only use a 3M™ Roloc® Bristle Disk (2-in white, part number 07528) to clean the crankshaft rear seal retainer plate and oil pan. Do not use metal scrapers, wire brushes or any other power abrasive disk to clean. These tools cause scratches and gouges that make leak paths.

Clean the crankshaft rear seal retainer plate and engine oil pan using a 3M™ Roloc® Bristle Disk (2-in white, part number 07528) in a suitable tool turning at the recommended speed of 15, 000 rpm.
- Thoroughly wash the crankshaft rear seal retainer plate and oil pan to remove any foreign material, including any abrasive particles created during the cleaning process.
NOTE: Place clean, lint free shop towels over exposed engine cavities. Carefully remove the towels so foreign material is not dropped into the engine. Any foreign material (including any material created while cleaning gaskets surfaces) that enters the oil passages or the oil pan, may cause engine failure.

NOTE: Do not use wire brushes, power abrasive discs or 3M™ Roloc® Bristle Disk (2-in white, part number 07528) to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. They also cause contamination that causes premature engine failure. Remove all traces of the gasket.

Clean the sealing surfaces of the cylinder block and oil pan flange in the following sequence.
1. Remove any large deposits of silicone or gasket material.
2. Apply silicone gasket remover and allow to set for several minutes.
3. Remove the silicone gasket remover. A second application of silicone gasket remover may be required if residual traces of silicone or gasket material remain.
4. Apply metal surface prep to remove any remaining traces of oil and to prepare the surfaces to bond. Do not attempt to make the metal shiny. Some staining of the metal surfaces is normal.