LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Mustang Base, 2D Coupe, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 180 (Engine Cooling System - F150) >> Removal And Installation >> Cooling Fan Motor and Shroud >> Removal and Installation

Removal and Installation

WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.

All engines 

  1. Disconnect the battery negative cable. For additional information, REFER to BATTERY, MOUNTING AND CABLES .
  2. Remove the Air Cleaner (ACL) outlet tube. For additional information, REFER to INTAKE AIR DISTRIBUTION & FILTERING .
  3. Remove the 4 pushpins and the upper radiator air deflector.
    Fig 1: Locating Upper Radiator Air Deflector And Pushpins
    G07411284Courtesy of FORD MOTOR CO.

    6.2L engines 

  4. Disconnect the Mass Air Flow (MAF) sensor electrical connector.
    Fig 2: Locating Mass Air Flow (MAF) Sensor Electrical Connector
    G07411334Courtesy of FORD MOTOR CO.
  5. Remove the 2 bolts and position the coolant expansion tank aside.
    Fig 3: Locating Coolant Expansion Tank Bolts
    G06126924Courtesy of FORD MOTOR CO.
  6. Detach the power steering fluid cooler hose retainer from the cooling fan motor and shroud.
  7. Detach the wiring harness retainer from the power steering fluid reservoir stud bolt.
  8. Remove the nut, detach the generator battery positive cable from the positive battery terminal, detach the 3 wiring harness retainers from the cooling fan shroud and position the wiring harness aside.
    • To install, tighten to 9 Nm (80 lb-in).
      Fig 4: Locating Wiring Harness Retainers To Cooling Fan Shroud
      G06455459Courtesy of FORD MOTOR CO.
  9. Detach the upper radiator hose retainer from the cooling fan motor and shroud.

    3.5L Gasoline Turbocharged Direct Injection (GTDI), 3.7L and 5.0L engines 

  10. Detach the wiring harness retainer from the stud bolt on the LH side of the cooling fan shroud.
  11. Disconnect the positive battery cable. For additional information, REFER to BATTERY, MOUNTING AND CABLES .
  12. Detach the battery cable retainer from the cooling fan shroud.

    All engines 

    13. NOTE: Push the 2 LH wiring harness retainer tabs outward to release.
    Fig 5: Pushing LH Wiring Harness Retainer Tabs
    G07411286Courtesy of FORD MOTOR CO.
  13. Detach the LH wiring harness retainer and the 3 RH wiring harness pushpins.
  14. Disconnect the 2 cooling fan electrical connectors.
  15. Detach the 3 cooling fan wiring harness retainers.
  16. Remove the 4 Battery Junction Box (BJB) bracket bolts.
    • To install, tighten to 10 Nm (89 lb-in).

    3.5L GTDI, 3.7L and 5.0L Engines 

  17. Position the wiring harness aside.

    6.2L engines 

  18. Remove the power steering fluid reservoir stud bolt and position the power steering fluid reservoir and the wiring harness aside.
    • To install, tighten to 11 Nm (97 lb-in).

    All engines 

  19. Remove the 2 bolts and the cooling fan motor and shroud.
    • To install, tighten to 7 Nm (62 lb-in).
  20. To install, reverse the removal procedure.
scientia non olet · About LEMON Manuals