DTC Charts
WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO FRONT CONTROL MODULE (ACM) - WITHOUT NAVIGATION DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST B . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST B . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST B . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST B . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST B . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST B . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST B . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST B . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum |
NOTE:
If DTC B1A56:21 sets after running the bezel diagnostic tests disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency the test will fail. Therefore test ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. DISREGARD this DTC. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST K . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST K . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST X . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to PINPOINT TEST AC . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AE . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST M . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO FRONT CONTROL MODULE (ACM) - WITH NAVIGATION DTC CHART
| DTC | Description | Action |
|---|---|---|
| B108E:63 | Display: Circuit / Component Protection Time-Out | GO to PINPOINT TEST T . |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST N . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST N . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B121C:44 | Hard Drive: Data Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:44 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A56:21 | Antenna: Signal Amplitude < Minimum |
NOTE:
If DTC B1A56:21 sets after running the bezel diagnostic tests disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency the test will fail. Therefore test ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. DISREGARD this DTC. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST K . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST K . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This can occur during extended use. Audio operation resumes after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D78:13 | Auxiliary Input: Circuit Open | GO to PINPOINT TEST E . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to PARKING AID . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST X . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST T . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST Y . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to PINPOINT TEST AC . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AE . |
| U2014:09 | Control Module Hardware: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:09 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST M . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST C . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST C . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST C . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST C . |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A06:11 | Speaker #6: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A06:12 | Speaker #6: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST C . |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A07:11 | Speaker #7: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A07:12 | Speaker #7: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST C . |
| B1A08:01 | Speaker #8: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A08:11 | Speaker #8: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A08:12 | Speaker #8: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST C . |
| B1A09:11 | Speaker #9: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A09:12 | Speaker #9: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST C . |
| B1A10:11 | Speaker #10: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A10:12 | Speaker #10: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST C . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U2014:01 | Control Module Hardware: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:01 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
FRONT CONTROLS INTERFACE MODULE (FCIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AA . |
| U2013:63 | Switch Pack: Circuit / Component Protection Time-Out | GO to PINPOINT TEST P . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
FRONT DISPLAY INTERFACE MODULE (FDIM) DTC CHART - WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B1318 | Battery Voltage Low | GO to PINPOINT TEST AJ . |
| B1342 | ECU is Faulted |
NOTE:
Repair all other DTCs before diagnosing DTC B1342. CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is the only DTC retrieved, INSTALL a new Front Display Interface Module (FDIM). REFER to FRONT DISPLAY INTERFACE MODULE (FDIM)
. REPEAT the self-test. |
| B2477 | Module Configuration Failure | REFER to MODULE CONFIGURATION . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST AG . |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Panel | GO to PINPOINT TEST AI . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | GO to PINPOINT TEST Y . |
| U0184 | Lost Communication With Radio (ACM) | GO to PINPOINT TEST AA . |
| U0197 | Lost Communication With Telephone Control Module | GO to PINPOINT TEST AB . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP) | GO to PINPOINT TEST AC . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION . |
| U2051 | One or More Calibration Files Missing/Corrupt | REFER to MODULE CONFIGURATION . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1252:04 | USB Port: System Internal Failure | GO to PINPOINT TEST G . |
| B1252:11 | USB Port: Circuit Short To Ground | GO to PINPOINT TEST G . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST S . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST AF . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AH . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC): No Sub Type Information | GO to PINPOINT TEST AI . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AE . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Body Control Module (BCM). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Global Positioning System Module (GPSM). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Front Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the APIM. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . TEST the system for normal operation. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the APIM. REFER to PMI in MODULE CONFIGURATION . TEST the system for normal operation. |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST R . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . TEST the system for normal operation. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . TEST the system for normal operation. |
| U3000:88 | Control Module: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
GLOBAL POSITIONING SYSTEM MODULE (GPSM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW diagnostics for other DTCs present in the Global Positioning System Module (GPSM) and Restraints Control Module (RCM). |
| U0423:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW diagnostics for other DTCs present in the GPSM and Instrument Panel Cluster (IPC). |
| U3000:09 | Control Module: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:09 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history
STEERING COLUMN CONTROL MODULE (SCCM) MODULE DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1380:09 | Steering Wheel Right Switch Pack: Component Failure | GO to PINPOINT TEST F . |
| B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to PINPOINT TEST F . |
| B1380:17 | Steering Wheel Right Switch Pack: Circuit Voltage Above Threshold | GO to PINPOINT TEST F . |
| All other DTCs | - | REFER to STEERING COLUMN SWITCHES . |