DTC Charts

WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.

BODY CONTROL MODULE (BCM) DTC CHART

DTC	Description	Action
B1175:01	Drivers Door Ajar Switch: General Electrical Failure	GO to Pinpoint Test F .
B1176:01	Passenger Door Ajar Switch: General Electrical Failure	GO to Pinpoint Test F .
B11C0:01	Driver Side Rear Door Ajar Switch: General Electrical Failure	GO to Pinpoint Test F .
B11C1:01	Passenger Side Rear Door Ajar Switch: General Electrical Failure	GO to Pinpoint Test F .
B12C2:11	Puddle Lamp: Circuit Short To Ground	GO to Pinpoint Test E .
B1313:11	Interior Lighting Output: Circuit Short To Ground	GO to Pinpoint Test C .
B1313:15	Interior Lighting Output: Circuit Short To Battery or Open	If the interior courtesy lamps are inoperative, GO to Pinpoint Test C . If the interior courtesy lamps stay on continuously, GO to Pinpoint Test G .
U1000:00	Solid State Driver Protection Active -Driver Disabled: No Sub Type Information	The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Body Control Module (BCM) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test.
U3000:49	Control Module: Internal Electronic Failure	The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation.
All other DTCs	-	REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES .

STEERING COLUMN CONTROL MODULE (SCCM) DTC CHART

DTC	Description	Action
B1124:09	Lamp Fade Control: Component Failure	REFER to INSTRUMENT CLUSTER AND PANEL ILLUMINATION .
All other DTCs	-	REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES .

INTERIOR LIGHTING CONTROL MODULE (ILCM) DTC CHART

DTC	Description	Action
B106E	Solid State Driver Disabled Due to Short Circuit	The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Interior Lighting Control Module (ILCM) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test.
B106F	Module Disabled Due to External Fault	The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the ILCM can withstand. The cause of the excessive current draw MUST be corrected before a new ILCM is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new ILCM. REFER to Interior Lighting Control Module (ILCM) . TEST the system for normal operation.
B1342	ECU Is Faulted	INSTALL a new ILCM. REFER to Interior Lighting Control Module (ILCM) . TEST the system for normal operation.
B2477	Module Configuration Failure	CARRY OUT the Programmable Module Installation (PMI) for the ILCM. REFER to MODULE CONFIGURATION . TEST the system for normal operation.
B2A21	One Or More Configuration Files Missing Or Corrupt	CARRY OUT the Programmable Module Installation (PMI) for the ILCM. REFER to MODULE CONFIGURATION . TEST the system for normal operation.
B2B00	Ambient Light Zone 1 Red Circuit Open	GO to Pinpoint Test L .
B2B01	Ambient Light Zone 1 Red Circuit Short to Ground	GO to Pinpoint Test L .
B2B02	Ambient Light Zone 1 Green Circuit Open	GO to Pinpoint Test L .
B2B03	Ambient Light Zone 1 Green Circuit Short to Ground	GO to Pinpoint Test L .
B2B04	Ambient Light Zone 1 Blue Circuit Open	GO to Pinpoint Test L .
B2B05	Ambient Light Zone 1 Blue Circuit Short to Ground	GO to Pinpoint Test L .
B2B18	Ambient Light Switch Input Fault	If the ambient lighting is inoperative or does not cycle through the color combinations, GO to Pinpoint Test K . If the ambient lighting does not cycle through the brightness settings, GO to Pinpoint Test M .
U0140	Lost Communication With Body Control Module (GEM)	GO to Pinpoint Test N .
U2050	No Application Present	REFER to MODULE CONFIGURATION .
All other DTCs	-	REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES .