Cylinder Head

WARNING: This page is about a different car, the 2012 Ford Pickup and 2012 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.

SPECIAL TOOLS CHART

	3 Jaw Puller 303-D121 or equivalent
	Adapter Set, Step Plate 205-DS011 or equivalent
	Lifting Bracket, Engine 303-F047 (014-00073) or equivalent
	Remover, Oil Seal 303-409 (T92C-6700-CH)
	Support Brackets, Engine 303-1507 or equivalent

MATERIAL SPECIFICATIONS

Item	Specification
Motorcraft® Metal Surface Prep ZC-31-A	-
Motorcraft® Silicone Gasket Remover ZC-30	-

NOTE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces that enters the oil passages, coolant passages or the oil pan, may cause engine failure.

NOTE: The flexplate and spacer plate must be removed before mounting the engine on the engine stand.

NOTE: For additional information, refer to the exploded view under the Assembly procedures.

All cylinder heads

Remove the engine. For additional information, refer to ENGINE removal.
Remove the 8 bolts and the flexplate.
- Discard the 8 flexplate bolts.
Fig 1: Locating Flexplate And Bolts
Courtesy of FORD MOTOR CO.
Remove the spacer plate.

Fig 2: Locating Spacer Plate
Courtesy of FORD MOTOR CO.
Disconnect the electrical connector and remove the bolt and the Crankshaft Position (CKP) sensor.

Fig 3: Locating Electrical Connector And Bolt Of Crankshaft Position Sensor
Courtesy of FORD MOTOR CO.
Mount the engine on a work stand.
Remove the Engine Lifting Brackets.

Fig 4: Removing Engine Lifting Brackets
Courtesy of FORD MOTOR CO.
Disconnect the Engine Oil Pressure (EOP) switch electrical connector and wiring harness retainer.

Fig 5: Locating Engine Oil Pressure Switch Electrical Connector And Wiring Harness Retainer
Courtesy of FORD MOTOR CO.
Disconnect the LH Variable Camshaft Timing (VCT) system oil control solenoid electrical connector and the 2 wiring harness retainers.

Fig 6: Locating LH Variable Camshaft Timing System Oil Control Solenoid Electrical Connector And Wiring Harness Retainers
Courtesy of FORD MOTOR CO.
Disconnect the 3 engine wiring harness position retainers from the LH valve cover.

Fig 7: Locating Engine Wiring Harness Position Retainers Of LH Valve Cover
Courtesy of FORD MOTOR CO.
Disconnect the wiring harness retainer, the Knock Sensor (KS) and Cylinder Head Temperature (CHT) sensor electrical connector.

Fig 8: Locating Wiring Harness Retainer, Knock Sensor And Cylinder Head Temperature Sensor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the LH and RH Camshaft Position (CMP) sensor electrical connectors.

Fig 9: Locating LH And RH Camshaft Position Sensor Electrical Connectors
Courtesy of FORD MOTOR CO.
Remove the nut and the radio interference capacitor.

Fig 10: Locating Radio Ignition Interference Capacitor Nut
Courtesy of FORD MOTOR CO.
Disconnect the RH Variable Camshaft Timing (VCT) system oil control solenoid electrical connector and the 2 wiring harness retainers.

Fig 11: Locating RH Variable Camshaft Timing System Oil Control Solenoid Electrical Connector And Wiring Harness Retainers
Courtesy of FORD MOTOR CO.
Disconnect the 3 engine wiring harness position retainers from the RH valve cover and remove the engine wiring harness.

Fig 12: Locating Engine Wiring Harness Position Retainers
Courtesy of FORD MOTOR CO.

NOTE: RH shown in illustration, LH similar.

Fig 13: Locating Ignition Wires Of Valve Cover Retainers And Lower Spark Plugs

Courtesy of FORD MOTOR CO.

Disconnect the 8 ignition wires from the valve cover retainers and the lower spark plugs.
Remove the 2 bolts and the LH and RH CMP sensors.

Fig 14: Locating LH And RH CMP Sensors Bolts
Courtesy of FORD MOTOR CO.

NOTE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use a plastic scraping tool to remove all traces of old sealant.

NOTE: Remove the valve cover carefully, or the Variable Camshaft Timing (VCT) solenoid may be damaged.

NOTE: The bolts are part of the valve cover and should not be removed.

Fig 15: Locating LH Valve Cover And Bolts

Courtesy of FORD MOTOR CO.

Loosen the 10 bolts and remove the LH valve cover and discard the gasket.
- Clean the valve cover mating surface of the cylinder head with silicone gasket remover and metal surface prep. Follow the directions on the packaging.
- Clean the valve cover gasket groove with soap and water or a suitable solvent.

NOTE: Remove the valve cover carefully, or the Variable Camshaft Timing (VCT) solenoid may be damaged.

NOTE: The bolts are part of the valve cover and should not be removed.

Fig 16: Locating RH Valve Cover And Bolts

Courtesy of FORD MOTOR CO.

Loosen the 10 bolts and remove the RH valve cover and discard the gasket.
- Clean the valve cover mating surface of the cylinder head with silicone gasket remover and metal surface prep. Follow the directions on the packaging.
- Clean the valve cover gasket groove with soap and water or a suitable solvent.
Remove the 6 bolts, the coolant pump pulley and the 2 accessory drive belt idler pulleys.

Fig 17: Locating Coolant Pump Pulley And Accessory Drive Belt Idler Pulleys Bolts
Courtesy of FORD MOTOR CO.
Remove the 3 bolts and the accessory drive belt tensioner.

Fig 18: Locating Accessory Drive Belt Tensioner Bolts
Courtesy of FORD MOTOR CO.
Remove the crankshaft pulley bolt.
- Discard the crankshaft pulley bolt.
Using the 3 Jaw Puller and Step Plate, remove the crankshaft pulley.

Fig 19: Removing Crankshaft Pulley
Courtesy of FORD MOTOR CO.

NOTE: Use care not to damage the engine front cover or the crankshaft when removing the seal.

Fig 20: Removing Crankshaft Front Oil Seal

Courtesy of FORD MOTOR CO.

Using the Oil Seal Remover, remove the crankshaft front oil seal.
Remove the front 4 oil pan bolts.

Fig 21: Locating Front Oil Pan Bolts
Courtesy of FORD MOTOR CO.

NOTE: Correct fastener location is essential for the assembly procedure. Record fastener location.

Fig 22: Locating Engine Front Cover Bolts And Studs

Courtesy of FORD MOTOR CO.

Remove the 17 bolts and the 3 studs.
Remove the engine front cover from the front cover-to-cylinder block dowel.
- Remove and discard the engine front cover gaskets.
Fig 23: Removing Engine Front Cover From Front Cover-To-Cylinder Block Dowel
Courtesy of FORD MOTOR CO.
Rotate the engine clockwise until the No. 1 intake valve is open.
Remove the 10 bolts and the LH intake rocker arm shaft assembly.

Fig 24: Locating LH Intake Rocker Arm Shaft Assembly Bolts
Courtesy of FORD MOTOR CO.
Rotate the engine clockwise until the No. 1 exhaust valve is open.
Remove the 10 bolts and the LH exhaust rocker arm shaft assembly.

Fig 25: Locating LH Exhaust Rocker Arm Shaft Assembly Bolts
Courtesy of FORD MOTOR CO.
Rotate the engine clockwise until the No. 1 intake valve is closed.
Remove the 10 bolts and the RH intake rocker arm shaft assembly.

Fig 26: Locating RH Intake Rocker Arm Shaft Assembly Bolts
Courtesy of FORD MOTOR CO.
Rotate the engine clockwise until the No. 1 exhaust valve is closed.
Remove the 10 bolts and the RH exhaust rocker arm shaft assembly.

Fig 27: Locating RH Exhaust Rocker Arm Shaft Assembly Bolts
Courtesy of FORD MOTOR CO.
Position the crankshaft keyway at the 11 o'clock position.

Fig 28: Locating Crankshaft Keyway
Courtesy of FORD MOTOR CO.
Remove the 2 bolts, the RH timing chain tensioner and tensioner arm.

Fig 29: Locating RH Timing Chain Tensioner And Tensioner Arm Bolts
Courtesy of FORD MOTOR CO.
Remove the bolt and the RH timing chain guide.

Fig 30: Locating RH Timing Chain Guide Bolt
Courtesy of FORD MOTOR CO.
Remove the RH timing chain.

Fig 31: Locating RH Timing Chain
Courtesy of FORD MOTOR CO.
Remove the 2 bolts and the LH timing chain tensioner.

Fig 32: Locating LH Timing Chain Tensioner Bolts
Courtesy of FORD MOTOR CO.
Remove the LH timing chain tensioner arm.

Fig 33: Locating LH Timing Chain Tensioner Arm
Courtesy of FORD MOTOR CO.
Remove the bolt and the LH timing chain guide.

Fig 34: Locating LH Timing Chain Guide And Bolt
Courtesy of FORD MOTOR CO.
Remove the LH timing chain.

Fig 35: Locating LH Timing Chain
Courtesy of FORD MOTOR CO.

LH cylinder head
Remove the 2 bolts and the LH exhaust manifold heat shield.

Fig 36: Locating Exhaust Manifold Heat Shield Bolts
Courtesy of FORD MOTOR CO.
Remove the 8 nuts, the 8 studs, the LH exhaust manifold and gaskets.
- Discard the 8 nuts and the 8 studs.
- Discard the 2 gasket.
- Inspect the exhaust manifold. For additional information, refer to ENGINE SYSTEM - GENERAL INFORMATION .
Fig 37: Locating LH Exhaust Manifold Nuts And Studs
Courtesy of FORD MOTOR CO.

NOTE: The cylinder head must be cool before removing it from the engine. Cylinder head warpage may result if a warm or hot cylinder head is removed.

NOTE: Place clean shop towels over exposed engine cavities. Carefully remove the towels so foreign material is not dropped into the engine.

NOTE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.

NOTE: Aluminum surfaces are soft and can be scratched easily. Never place the cylinder head gasket surface, unprotected, on a bench surface, or the cylinder head may be damaged.

NOTE: The cylinder head bolts must be discarded and new bolts must be installed. They are a tighten-to-yield design and cannot be reused.

Fig 38: Locating LH Cylinder Head And Bolts

Courtesy of FORD MOTOR CO.

Remove the 11 bolts and the LH cylinder head.
- Discard the cylinder head gasket.
- Discard the 11 cylinder head bolts.
RH cylinder head
Remove the 2 bolts and the RH exhaust manifold heat shield.

Fig 39: Locating RH Exhaust Manifold Heat Shield Bolts
Courtesy of FORD MOTOR CO.
Remove the 8 nuts, the 8 studs, the RH exhaust manifold and gaskets.
- Discard the 8 nuts and the 8 studs.
- Discard the 2 gasket.
- Inspect the exhaust manifold. For additional information, refer to ENGINE SYSTEM - GENERAL INFORMATION .
Fig 40: Locating RH Exhaust Manifold Nuts And Studs
Courtesy of FORD MOTOR CO.

NOTE: The engine support insulator bracket bolts must be discarded and new bolts installed or damage to the vehicle may occur. They are a tighten-to-yield design and cannot be reused.

Fig 41: Locating RH Engine Support Insulator-To-Cylinder Block Bracket And Bolts

Courtesy of FORD MOTOR CO.

Remove the 4 bolts and the RH engine support insulator-to-cylinder block bracket.
- Discard the 4 support insulator-to-cylinder block bolts.
Remove the bolt and the oil level indicator tube.
- Discard the O-ring seal.
Fig 42: Locating Oil Level Indicator Tube And Bolt
Courtesy of FORD MOTOR CO.
Remove the nut and the ground strap.

Fig 43: Locating Nut And Ground Strap
Courtesy of FORD MOTOR CO.

NOTE: The cylinder head must be cool before removing it from the engine. Cylinder head warpage may result if a warm or hot cylinder head is removed.

NOTE: Place clean shop towels over exposed engine cavities. Carefully remove the towels so foreign material is not dropped into the engine.

NOTE: Aluminum surfaces are soft and can be scratched easily. Never place the cylinder head gasket surface, unprotected, on a bench surface, or the cylinder head may be damaged.

NOTE: The cylinder head bolts must be discarded and new bolts must be installed. They are a tighten-to-yield design and cannot be reused.

Fig 44: Locating RH Cylinder Head And Bolts

Courtesy of FORD MOTOR CO.

Remove the 10 bolts and the RH cylinder head.
- Discard the cylinder head gasket.
- Discard the 10 cylinder head bolts.
All cylinder heads

NOTE: Observe all warnings or cautions and follow all application directions contained on the packaging of the silicone gasket remover and the metal surface prep.

NOTE: If there is no residual gasket material present, metal surface prep can be used to clean and prepare the surfaces.

Clean the cylinder head-to-cylinder block mating surfaces of both the cylinder head and the cylinder block in the following sequence.
1. Remove any large deposits of silicone or gasket material with a plastic scraper.
2. Apply silicone gasket remover, following package directions and allow to set for several minutes.
3. Remove the silicone gasket remover with a plastic scraper. A second application of silicone gasket remover may be required if residual traces of silicone or gasket material remain.
4. Apply metal surface prep, following package directions, to remove any remaining traces of oil or coolant and to prepare the surfaces to bond with the new gasket. Do not attempt to make the metal shiny. Some staining of the metal surfaces is normal.
Support the cylinder heads on a bench with the head gasket side up. Check the cylinder head distortion and the cylinder block distortion, paying particular attention to the oil pressure feed area. For additional information, refer to ENGINE SYSTEM - GENERAL INFORMATION .