Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
BODY CONTROL MODULE (BCM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1115:11 | High Mounted Stop Lamp Control: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B123A:11 | Left Front Turn Indicator: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B123A:15 | Left Front Turn Indicator: Circuit Short To Battery or Open | GO to PINPOINT TEST M . |
| B123B:11 | Right Front Turn Indicator: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B123B:15 | Right Front Turn Indicator: Circuit Short To Battery or Open | GO to PINPOINT TEST M . |
| B1277:11 | Reverse Lamp: Circuit Short To Ground | GO to PINPOINT TEST U . |
| B1277:15 | Reverse Lamp: Circuit Short To Battery or Open | If the reverse lamps are inoperative, GO to PINPOINT TEST U . If the reverse lamps are always on, GO to PINPOINT TEST W . |
| B130C:12 | Load Shed Control: Circuit Short To Battery | GO to PINPOINT TEST AC . |
| B130C:14 | Load Shed Control: Circuit Short To Ground or Open | GO to PINPOINT TEST AC . |
| B132B:11 | Left Stop/Turn Lamp: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B132B:15 | Left Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to PINPOINT TEST J . If the stoplamp is always on, GO to PINPOINT TEST K . |
| B132C:11 | Right Stop/Turn Lamp: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B132C:15 | Right Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to PINPOINT TEST J . If the stoplamp is always on, GO to PINPOINT TEST K . |
| B1A85:11 | Ambient Light Sensor: Circuit Short To Ground | GO to PINPOINT TEST H . |
| B1A85:13 | Ambient Light Sensor: Circuit Open | GO to PINPOINT TEST H . |
| B1C98:11 | Left Corner Lamp Circuit: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B1C99:11 | Right Corner Lamp Circuit: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B1D00:11 | Left Low Beam: Circuit Short To Ground | GO to PINPOINT TEST A . |
| B1D01:11 | Right Low Beam: Circuit Short To Ground | GO to PINPOINT TEST A . |
| B1D02:11 | Left High Beam Circuit: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B1D02:15 | Left High Beam Circuit: Circuit Short To Battery or Open | If the high beam is inoperative, GO to PINPOINT TEST B . If the high beam is always on, GO to PINPOINT TEST D . |
| B1D03:11 | Right High Beam Circuit: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B1D03:15 | Right High Beam Circuit: Circuit Short To Battery or Open | If the high beam is inoperative, GO to PINPOINT TEST B . If the high beam is always on, GO to PINPOINT TEST D . |
| B1D35:11 | Hazard Switch: Circuit Short To Ground | GO to PINPOINT TEST N . |
| C0040:12 | Brake Pedal Switch "A": Circuit Short To Battery | GO to PINPOINT TEST K . |
| U1000:00 | Solid State Driver Protection Active - Driver Disabled: No Sub Type Information | The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Body Control Module (BCM) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test. |
| U3000:49 | Control Module: Internal Electronic Failure | The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |
STEERING COLUMN CONTROL MODULE (SCCM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1007:09 | High-Beam Headlamp Switch: Component Failure | INSTALL a new multifunction switch. REFER to STEERING COLUMN SWITCHES . TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM. REFER to STEERING COLUMN SWITCHES . TEST the system for normal operation. |
| B10A6:09 | Main Light Switch: Component Failure | GO to PINPOINT TEST C . |
| B1D36:09 | Turn Indicator Switch: Component Failure | If the turn lamp function is inoperative, GO to PINPOINT TEST L . If the turn lamp function is always on, INSTALL a new multifunction switch. REFER to STEERING COLUMN SWITCHES . TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM. REFER to STEERING COLUMN SWITCHES . TEST the system for normal operation. |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |