LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Focus S, Standard Trans, Gas >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Except Electric) - Pinpoint Tests (B0004 - B11D8) >> Pinpoint Test - Vehicles Built Up To: 25-June-2012, DTC: B11D8:12 and B11D8:14 >> B11D8:12 and B11D8:14 >> Normal Operation and Fault Conditions >> Pinpoint Test A : B11D8:12 And B11D8:14

Pinpoint Test A : B11D8:12 And B11D8:14

WARNING: Do not handle, move or change the original horizontal mounting position of the Restraints Control Module (RCM) while the Restraints Control Module (RCM) is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy® and cause serious personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: Install new components only when directed to do so in the pinpoint test.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS) 
    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:12 or B11D8:14 retrieved on-dem and during self-test? 

    1. Yes:  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-dem and during the self-test. For DTC B11D8:14, GO to A2 For DTC B11D8:12, GO to  A6
    2. No:  This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to  A11
  2. A2 CHECK THE EVENT NOTIFICATION SIGNAL CIRCUIT FOR AN OPEN 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C310A-23 Ω C4805E-21
    • Measure:

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C310A-23 Ω C2280C-51

    Are the resistances less than 3 ohms? 

    1. Yes:  GO to A3
    2. No:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A12

  3. A3 CHECK THE EVENT NOTIFICATION SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    • Measure:

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C2280C-51 Ω -

    Is the resistance greater than 10, 000 ohms? 

    1. Yes:  CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM.

      REFER to: Body Control Module (BCM)  ( BODY CONTROL MODULE (BCM) ).

      GO to A4

    2. No:  REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A12

  4. A4 CONFIRM THE BCM (BODY CONTROL MODULE) REPAIR 
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B.
    • Connect BCM C2280C.
    • Connect Upper High Voltage Battery Pack C4805E.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Clear Diagnostic Trouble Codes (DTCs) - RCM.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:14 retrieved on-dem and during self-test? 

    1. Yes:  INSTALL a new RCM.

      REFER to: Restraints Control Module (RCM) .

      GO to A5

    2. No:  GO to  A12
  5. A5 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) REPAIR 
    • Enter the following diagnostic mode: Clear Diagnostic Trouble Codes (DTCs) - RCM.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:14 retrieved on-dem and during self-test? 

    1. Yes:  GO to  A8
    2. No:  GO to  A12
  6. A6 CHECK THE EVENT NOTIFICATION SIGNAL CIRCUIT DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Disconnect BCM C2280C.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:12 retrieved on-dem and during self-test? 

    1. Yes:  CONNECT BCM C2280C. GO to A7
    2. No:  CONNECT BCM C2280C. CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM.

      REFER to: Body Control Module (BCM)  ( BODY CONTROL MODULE (BCM) ).

      GO to  A12

  7. A7 CHECK THE EVENT NOTIFICATION SIGNAL CIRCUIT DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE WITH THE BATTERY ENERGY CONTROL MODULE (BECM) DISCONNECTED 
    • Ignition OFF.
    • Disconnect Upper High Voltage Battery Pack C4805E.
    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:12 retrieved on-dem and during self-test? 

    1. Yes:  GO to  A9
    2. No:  GO to A8
  8. A8 CONFIRM THE HIGH VOLTAGE BATTERY FAULT 
    • Ignition OFF.
    • Disconnect Upper High Voltage Battery Pack C4805E.
    • Inspect Upper High Voltage Battery Pack C4805Efor:

      pushed-out, loose or spread terminal and loose or frayed wire connections at terminals.

      any damaged, pinched, cut or pierced wires.

      corrosion.

    • Repair any concerns found.
    • Connect Upper High Voltage Battery Pack C4805E.
    • Ignition ON.
    • Enter the following diagnostic mode: Clear Diagnostic Trouble Codes (DTCs) - RCM.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:14 retrieved on-dem and during self-test? 

    1. Yes:  CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new upper and lower high voltage battery pack. For the upper high voltage battery pack, For the lower high voltage battery pack, GO to  A12
    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to  A11
  9. A9 CHECK THE EVENT NOTIFICATION SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 

    Click to display connectors 

    Positive Lead Measurement / Action Negative Lead
    C2280C-51
    G08101551
    		 -

    Is any voltage present? 

    1. Yes:  CONNECT BCM C2280C. REPAIR the circuit.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

      GO to  A12

    2. No:  CONNECT BCM C2280C. GO to A10
  10. A10 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT 
    NOTE: Make sure all SRS electrical connectors and the BCM electrical connector are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect BCM C2280C(if not previously disconnected).
    • Disconnect Upper High Voltage Battery Pack C4805E (if not previously disconnected).
    • Disconnect RCM C310A and C310B (if not previously disconnected).
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B.
    • Connect Upper High Voltage Battery Pack C4805E.
    • Connect BCM C2280C.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: DataLogger - RCM.

    Was the original DTC retrieved on-dem and during self-test? 

    1. Yes:  CHECK OASIS  for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM.

      REFER to: Restraints Control Module (RCM) .

      GO to  A12

    2. No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to A11
  11. A11 CHECK FOR AN INTERMITTENT FAULT 
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Ignition OFF.
    • Depower the SRS.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Disconnect RCM C310A and C310B.
    • Disconnect Upper High Voltage Battery Pack C4805E.
    • Disconnect BCM C2280C.
      • inspect connector(s) (including any inline connectors) for loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • repair any concerns found.

        Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect BCM C2280C.
    • Connect Upper High Voltage Battery Pack C4805E.
    • Connect RCM C310A and C310B.
    • Repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - RCM.

    Was DTC B11D8:12 or B11D8:14 retrieved on-dem and during self-test? 

    1. Yes:  The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-dem and during the self-test. For DTC B11D8:14, GO to  A2 For DTC B11D8:12, GO to  A6
    2. No:  CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition frequently. ACTIVATE other systems in the same wire harness. Do not install any new SRS components at this time. Only install SRS components when directed to do so in the pinpoint test. REPAIR any intermittent concerns found. GO to A12
  12. A12 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS) 
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Ignition OFF.
    • Reconnect all connectors (if previously disconnected).
    • If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time.

      REFER to: Supplemental Restraint System (SRS) Depowering and Repowering .

    • Ignition ON.
    • Enter the following diagnostic mode: Self Test - Restraints.
      NOTE: When selecting Restraints from the Self Test menu, Diagnostic Trouble Codes (DTCs) are retrieved from the RCM and OCSM.

    Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved? 

    1. Yes:  Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. Refer to RCM DTC CHART or Refer to OCSM DTC CHART for pinpoint test direction.
    2. No:  CLEAR all Diagnostic Trouble Codes (DTCs) in all modules. PROVE OUT the SRS. The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals