DTC Chart
WARNING: This page is about a different car, the 2013 Ford F-550 Super Duty, 2013 Ford F-450 Super Duty, 2013 Ford F-350 Super Duty, and 2013 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
The DTCs can be retrieved from the RCM with a scan tool via the DLC.
NOTE:
Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE:
Network DTCs (U-codes) are often a result of intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often set network DTCs. Replacing a module to resolve a network DTC is unlikely to resolve the concern. To prevent repeat network DTC concerns, inspect all network wiring, especially connectors. Test the vehicle battery, refer to
BATTERY, MOUNTING AND CABLES
.
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure type code. The failure type code provides information about specific fault conditions such as opens or shorts to ground. CMDTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
RCM DTC CHART
| DTC | Description | Action To Take |
|---|---|---|
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST B . |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST B . |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to PINPOINT TEST B . |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST B . |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to PINPOINT TEST C . |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST C . |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0020:11 | Left Side Airbag Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST D . |
| B0020:12 | Left Side Airbag Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST D . |
| B0020:13 | Left Side Airbag Deployment Control: Circuit Open | GO to PINPOINT TEST D . |
| B0020:1A | Left Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST D . |
| B0020:2B | Left Side Airbag Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0020:4A | Left Side Airbag Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0021:11 | Left Curtain Deployment Control 1: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B0021:12 | Left Curtain Deployment Control 1: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B0021:13 | Left Curtain Deployment Control 1: Circuit Open | GO to PINPOINT TEST E . |
| B0021:1A | Left Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to PINPOINT TEST E . |
| B0021:2B | Left Curtain Deployment Control 1: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0021:4A | Left Curtain Deployment Control 1: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0028:11 | Right Side Airbag Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B0028:12 | Right Side Airbag Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B0028:13 | Right Side Airbag Deployment Control: Circuit Open | GO to PINPOINT TEST F . |
| B0028:1A | Right Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST F . |
| B0028:2B | Right Side Airbag Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0028:4A | Right Side Airbag Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0029:11 | Right Curtain Deployment Control 1: Circuit Short to Ground | GO to PINPOINT TEST G . |
| B0029:12 | Right Curtain Deployment Control 1: Circuit Short to Battery | GO to PINPOINT TEST G . |
| B0029:13 | Right Curtain Deployment Control 1: Circuit Open | GO to PINPOINT TEST G . |
| B0029:1A | Right Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to PINPOINT TEST G . |
| B0029:2B | Right Curtain Deployment Control 1: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0029:4A | Right Curtain Deployment Control 1: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to PINPOINT TEST H . |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to PINPOINT TEST H . |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to PINPOINT TEST H . |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to PINPOINT TEST H . |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0090:11 | Left Frontal Restraints Sensor: Circuit Short to Ground | GO to PINPOINT TEST I . |
| B0090:4A | Left Frontal Restraints Sensor: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0090:81 | Left Frontal Restraints Sensor: Invalid Serial Data Received | INSTALL a new front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR . |
| B0090:93 | Left Frontal Restraints Sensor: No Operation | GO to PINPOINT TEST I . |
| B0090:96 | Left Frontal Restraints Sensor: Component Internal Failure | INSTALL a new front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR . |
| B0091:11 | Left Side Restraints Sensor 1: Circuit Short to Ground | GO to PINPOINT TEST J . |
| B0091:4A | Left Side Restraints Sensor 1: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0091:81 | Left Side Restraints Sensor 1: Invalid Serial Data Received | INSTALL a new driver door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . |
| B0091:93 | Left Side Restraints Sensor 1: No Operation | GO to PINPOINT TEST J . |
| B0091:96 | Left Side Restraints Sensor 1: Component Internal Failure | INSTALL a new driver door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . |
| B0092:11 | Left Side Restraints Sensor 2: Circuit Short to Ground | GO to PINPOINT TEST K . |
| B0092:4A | Left Side Restraints Sensor 2: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0092:81 | Left Side Restraints Sensor 2: Invalid Serial Data Received | INSTALL a new driver C-pillar side impact sensor. REFER to SIDE IMPACT SENSOR - SECOND ROW, SUPERCAB or SIDE IMPACT SENSOR - SECOND ROW, CREW CAB . |
| B0092:93 | Left Side Restraints Sensor 2: No Operation | GO to PINPOINT TEST K . |
| B0092:96 | Left Side Restraints Sensor 2: Component Internal Failure | INSTALL a new driver C-pillar side impact sensor. REFER to SIDE IMPACT SENSOR - SECOND ROW, SUPERCAB or SIDE IMPACT SENSOR - SECOND ROW, CREW CAB . |
| B0096:11 | Right Side Restraints Sensor 1: Circuit Short to Ground | GO to PINPOINT TEST K . |
| B0096:4A | Right Side Restraints Sensor 1: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0096:81 | Right Side Restraints Sensor 1: Invalid Serial Data Received | INSTALL a new passenger door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . |
| B0096:93 | Right Side Restraints Sensor 1: No Operation | GO to PINPOINT TEST K . |
| B0096:96 | Right Side Restraints Sensor 1: Component Internal Failure | INSTALL a new passenger door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR . |
| B0097:11 | Right Side Restraints Sensor 2: Circuit Short to Ground | GO to PINPOINT TEST J . |
| B0097:4A | Right Side Restraints Sensor 2: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B0097:81 | Right Side Restraints Sensor 2: Invalid Serial Data Received | INSTALL a new passenger C-pillar side impact sensor. REFER to SIDE IMPACT SENSOR - SECOND ROW, SUPERCAB or SIDE IMPACT SENSOR - SECOND ROW, CREW CAB . |
| B0097:93 | Right Side Restraints Sensor 2: No Operation | GO to PINPOINT TEST J . |
| B0097:96 | Right Side Restraints Sensor 2: Component Internal Failure | INSTALL a new passenger C-pillar side impact sensor. REFER to SIDE IMPACT SENSOR - SECOND ROW, SUPERCAB or SIDE IMPACT SENSOR - SECOND ROW, CREW CAB . |
| B00D5:01 | Restraint System Passenger Disable Indicator: General Electrical Failure | CONFIGURE the RCM using As-Built data. CLEAR all RCM DTCs and REPEAT the self-test. If DTC B00D5:01 returns, the RCM has received a fault message from the FCIM indicating a fault in the PAD indicator. CARRY OUT a self-test of the FCIM and REPAIR any DTCs. Do not replace the RCM for this DTC. |
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short to Ground | GO to PINPOINT TEST L . |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short to Battery | GO to PINPOINT TEST L . |
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | GO to PINPOINT TEST L . |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B00DF:11 | Passenger Restraints Disable Switch: Circuit Short to Ground | GO to PINPOINT TEST M . |
| B00DF:12 | Passenger Restraints Disable Switch: Circuit Short to Battery | GO to PINPOINT TEST M . |
| B00DF:13 | Passenger Restraints Disable Switch: Circuit Open | GO to PINPOINT TEST M . |
| B00DF:1D | Passenger Restraints Disable Switch: Circuit Current Out of Range | GO to PINPOINT TEST M . |
| B00DF:2B | Passenger Restraints Disable Switch: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B00DF:4A | Passenger Restraints Disable Switch: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | This DTC indicates the vehicle has been involved in a collision. INSTALL a new RCM and impact sensors. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT . |
| B11D8:12 | Restraint Event Notification: Circuit Short to Battery | GO to PINPOINT TEST U . |
| B11D8:14 | Restraint Event Notification: Circuit Short to Ground or Open | GO to PINPOINT TEST U . |
| B1202:01 | Restraint System Passenger Enable Indicator: General Electrical Failure | The RCM has received a fault message from the FCIM indicating a fault in the PAD indicator. CARRY OUT a self-test of the FCIM and REPAIR any DTCs. Do not replace the RCM for this DTC. |
| B1211:11 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST N . |
| B1211:12 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST N . |
| B1211:13 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | GO to PINPOINT TEST N . |
| B1211:1A | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST N . |
| B1211:2B | Driver Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B1211:4A | Driver Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| B1214:11 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | GO to PINPOINT TEST O . |
| B1214:12 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | GO to PINPOINT TEST O . |
| B1214:13 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | GO to PINPOINT TEST O . |
| B1214:1A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to PINPOINT TEST O . |
| B1214:2B | Passenger Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | GO to PINPOINT TEST P . |
| B1214:4A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | GO to PINPOINT TEST R . |
| U0028:88 | Vehicle Communication Bus A: Bus Off | GO to PINPOINT TEST R . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose the lost communication with the BCM. |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose the lost communication with the IPC. |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC sets in the RCM if a message is not received from the APIM. CHECK for additional RCM and APIM DTCs. REFER to the DTC CHARTS to diagnose any RCM DTCs. For APIM DTC's, Refer to the appropriate Information and Entertainment Systems article for the procedure. |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CARRY OUT PMI. REFER to MODULE CONFIGURATION . RETRIEVE any RCM DTCs. If RCM DTC U0300:00 is retrieved on-demand during the self-test, INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | CARRY OUT self-test of the PCM and diagnose any DTCs present. REFER to appropriate "Engine Controls" article or the DTC Chart in ELECTRONIC ENGINE CONTROLS - GASOLINE ENGINES or ELECTRONIC ENGINE CONTROLS - DIESEL ENGINES . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | CARRY OUT a self-test of the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES to diagnose any DTCs that are retrieved. |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | CHECK for additional RCM and APIM DTCs. REFER to the DTC CHARTS to diagnose any RCM DTCs. For APIM DTC's, Refer to the appropriate Information and Entertainment Systems article for the procedure. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CARRY OUT PMI. REFER to MODULE CONFIGURATION . RETRIEVE RCM DTCs. If RCM DTC U2100:00 is retrieved, INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | INSTALL a new RCM and CARRY OUT PMI using as-built data when carrying out PMI. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U2300:55 | Central Configuration: Not Configured | GO to PINPOINT TEST T . |
| U2300:64 | Central Configuration: Signal Plausibility Failure | GO to PINPOINT TEST T . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new RCM and CARRY OUT PMI. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new RCM and CARRY OUT PMI. If DTC U2200:00 is also present, use as-built data when CARRYING out PMI. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U3000:4A | Control Module: Incorrect Component Installed | GO to PINPOINT TEST Q . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST S . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST S . |