LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Explorer Limited, 3.5 8, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 332 (Supplemental Restraint System - Pinpoint Tests A - Z) >> Pinpoint Test L: B0082:11, B0082:12, B0082:13 and B0082:1A >> Pinpoint Test L: B0082:11, B0082:12, B0082:13 and B0082:1A

Pinpoint Test L: B0082:11, B0082:12, B0082:13 and B0082:1A

WARNING: This page is about a different car, the 2013 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM  is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy and cause serious personal injury or death.
WARNING: Never disassemble or tamper with seat belt deployable components, including pretensioners, load limiters and inflators. Never back probe deployable device electrical connectors. Tampering or back probing may cause an accidental deployment and result in personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS  components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs  may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
  1. L1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B0082:11, B0082:12, B0082:13 or B0082:1A retrieved on-demand during self-test? 

    1. Yes  : This fault cannot be cleared until it is corrected and the DTC  is no longer retrieved on-demand during self-test.

      For DTC  B0082:13 or B0082:1A, GO to L2  .

      For DTC  B0082:11, GO to  L8.

      For DTC  B0082:12, GO to  L10.

    2. No  : This is an intermittent fault when present as a CMDTC only.

      For DTC  B0082:13 or B0082:1A, GO to  L13.

      For DTC  B0082:11, GO to  L14.

      For DTC  B0082:12, GO to  L15.

  2. L2 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID 
    • Using a scan tool, view RCM PIDs  .
    • Monitor and record the resistance value displayed by the DEPLOY_26_R PID  .

    Does the PID value read between 1.44 and 3.52 ohms? 

    1. Yes  : GO to L12  .
    2. No  : GO to L3  .
  3. L3 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID WHILE CARRYING OUT THE HARNESS TEST 
    • While monitoring the DEPLOY_26_R PID  , carry out the harness test of the passenger safety belt load limiter circuits and accessible connectors (including any inline connectors) by wiggling and flexing the wire harness and connectors frequently. Record the resistance value indicated by the PID  .

    Does the PID value read between 1.44 and 3.52 ohms while carrying out the harness test? 

    1. Yes  : DEPOWER the SRS  and REPAIR the connector, terminals or wire harness as needed.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

    2. No  : For PID  value less than 1.44 ohms, GO to L4  .

      For PID  value greater than 3.52 ohms, GO to  L6.

  4. L4 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.

    Did the on-demand DTC change from B0082:1A to B0082:13? 

    1. Yes  : GO to  L11.
    2. No  : GO to L5  .
  5. L5 CHECK FOR A SHORT BETWEEN PASSENGER SAFETY BELT LOAD LIMITER CIRCUITS 

    Is the resistance greater than 10, 000 ohms? 

    1. Yes  : GO to L12  .
    2. No  : REPAIR the circuits.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

  6. L6 CHECK THE PASSENGER SAFETY BELT LOAD LIMITER CIRCUITS FOR AN OPEN 

    Are the resistances less than 0.5 ohm? 

    1. Yes  : GO to L7  .
    2. No  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

  7. L7 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.

    Did the on-demand DTC change from B0082:13 to B0082:1A? 

    1. Yes  : REMOVE the fused jumper wire and GO to  L11.
    2. No  : REMOVE the fused jumper wire and GO to L12  .
  8. L8 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM  by inducing a different fault condition. If the reported fault changes, this indicates the RCM  is functioning correctly and is not the source of the fault.

    Did the on-demand DTC change from B0082:11 to B0082:13? 

    1. Yes  : GO to  L11.
    2. No  : GO to L9  .
  9. L9 CHECK THE PASSENGER SAFETY BELT LOAD LIMITER CIRCUITS FOR A SHORT TO GROUND 

    Are the resistances greater than 10, 000 ohms? 

    1. Yes  : GO to L12  .
    2. No  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

  10. L10 CHECK THE PASSENGER SAFETY BELT LOAD LIMITER CIRCUITS FOR A SHORT TO VOLTAGE 

    Is any voltage present? 

    1. Yes  : REPAIR the circuit(s).

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

    2. No  : GO to L12  .
  11. L11 CONFIRM THE PASSENGER SAFETY BELT RETRACTOR FAULT 
    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs  will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : INSTALL a new passenger safety belt retractor. REFER to SAFETY BELT RETRACTOR AND PRETENSIONER . GO to  L17.
    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  .

      For DTC  B0082:13 or B0082:1A, GO to  L13.

      For DTC  B0082:11, GO to  L14.

      For DTC  B0082:12, GO to  L15.

    NOTE: Make sure all SRS  components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs  will be recorded.

    Was the original DTC retrieved on-demand during self-test? 

    1. Yes  : CHECK OASIS  for any applicable TSBs  . If a TSB  exists for this concern, discontinue this test and follow TSB  instructions. If no TSBs  address this concern, INSTALL a new RCM  . Refer to RESTRAINTS CONTROL MODULE (RCM) . GO to  L17.
    2. No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  .

      For DTC  B0082:13 or B0082:1A, GO to L13  .

      For DTC  B0082:11, GO to  L14.

      For DTC  B0082:12, GO to  L15.

  12. L13 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT 
    • Using a scan tool, view RCM PIDs  .
    • While monitoring the DEPLOY_26_R PID  , attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently. Record the resistance value indicated by the PID  .

    Does the PID value read between 1.44 and 3.52 ohms? 

    1. Yes  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  L16.
    2. No  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

  13. L14 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO GROUND FAULT 
    • Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.
    • Using a scan tool, perform RCM  self-test to retrieve DTCs  .

    Was DTC B0082:11 retrieved on-demand during self-test? 

    1. Yes  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to  L16.
  14. L15 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO BATTERY FAULT 

    Was DTC B0082:12 retrieved on-demand during self-test? 

    1. Yes  : DEPOWER the SRS  and REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to  L17.

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to L16  .
  15. L16 CHECK THE HARNESS AND CONNECTORS 

    Were any concerns found? 

    1. Yes  : REPAIR as necessary.

      Refer to OEM CONNECTOR REPAIR PROCEDURES for connector information.

      GO to L17  .

    2. No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test  . GO to L17  .
  16. L17 CHECK FOR ADDITIONAL SRS DTCs 

    Are any RCM and/or OCSM DTCs retrieved on-demand during self-test? 

    1. Yes  : Do not clear any DTCs  until all DTCs  have been resolved. REFER to the appropriate DTC CHART in this information for pinpoint test direction.
    2. No  : CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals