Camshaft - RH: Installation

WARNING: This page is about a different car, the 2013 Ford F-550 Super Duty and 2013 Ford F-450 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

Lubricate the camshaft and camshaft journals with clean engine oil.
NOTE: Do not remove the Timing Chain Locking Tool at any time during assembly. If the Timing Chain Locking Tool is removed or out of placement, the engine front cover must be removed and the engine must be retimed. For additional information, refer to TIMING DRIVE COMPONENTS .

NOTE: Do not allow the roller followers to move out of position when installing the camshaft.

Install the camshaft into the camshaft sprocket assembly and onto the head. Install a new camshaft sprocket bolt finger-tight.

Fig 1: Locating RH Camshaft Sprocket Bolt
Courtesy of FORD MOTOR CO.
NOTE: Do not remove the Timing Chain Locking Tool at any time during assembly. If the Timing Chain Locking Tool is removed or out of placement, the engine front cover must be removed and the engine must be retimed. For additional information, refer to TIMING DRIVE COMPONENTS .

NOTE: The timing chain must be installed in its original position onto the camshaft sprocket using the scribed marks, or damage to valves and pistons will result.

Verify the camshaft sprocket and timing chain scribe marks are still in alignment.

Fig 2: Locating Scribed Mark On Timing Chain And Camshaft Sprocket Assembly
Courtesy of FORD MOTOR CO.
NOTE: Do not allow the roller followers to move out of position when installing the camshaft.

Install the camshaft bearing caps in their original locations.
- Lubricate the camshaft bearing caps with clean engine oil.
- Position the front camshaft bearing cap.
- Position the remaining camshaft bearing caps.
- Install the 12 bolts loosely.
Tighten the 12 RH camshaft bearing cap bolts in 2 stages:
- Stage 1: Tighten to 8 Nm (71 lb-in) in the sequence shown in the illustration.
- Stage 2: Tighten an additional 45 degrees.
  
  Fig 3: Identifying RH Camshaft Bearing Cap Bolts Tightening Sequence
  Courtesy of FORD MOTOR CO.
Remove the Timing Chain Locking Tool.

Fig 4: Identifying Timing Chain Locking Tool
Courtesy of FORD MOTOR CO.
Rotate the crankshaft a half turn counterclockwise and position the crankshaft damper spoke at the 12 o'clock position and the timing mark indentation at the 1 o'clock position.

Fig 5: Positioning Timing Mark Indentation At 1 O'Clock Position
Courtesy of FORD MOTOR CO.
The No. 1 cylinder camshaft exhaust lobe must be coming up on the exhaust stroke. Verify by noting the position of the 2 intake camshaft lobes and the exhaust lobe on the No. 1 cylinder.

Fig 6: Identifying Camshaft Lobe Position
Courtesy of FORD MOTOR CO.
NOTE: Lubricate the camshaft roller followers with clean engine oil prior to installation.

NOTE: Do not allow the valve keepers to fall off the valve or the valve may drop into the cylinder. If a valve drops into the cylinder, the cylinder head must be removed. For additional information, refer to CYLINDER HEAD .

NOTE: It may be necessary to push the valve down while compressing the spring.

Using the Valve Spring Compressor, install the 3 originally removed camshaft roller followers.

Fig 7: Identifying Valve Spring Compressor
Courtesy of FORD MOTOR CO.
Install the CMP sensor and the bolt.

Fig 8: Locating Camshaft Position Sensor Mounting Bolt
Courtesy of FORD MOTOR CO.
Connect the CMP electrical connector.

Fig 9: Locating Camshaft Position Sensor Electrical Connector
Courtesy of FORD MOTOR CO.
NOTE: Only use hand tools to install the camshaft sprocket assembly or damage may occur to the camshaft or camshaft sprocket.

Tighten the camshaft sprocket bolt in 2 stages:
- Stage 1: Tighten to 40 Nm (30 lb-ft).
- Stage 2: Tighten an additional 90 degrees.
  
  Fig 10: Locating RH Camshaft Sprocket Bolt
  Courtesy of FORD MOTOR CO.
Install the RH valve cover. For additional information, refer to VALVE COVER - RH .