DTC Charts
WARNING: This page is about a different car, the 2013 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
For SYNC® related concerns, REFER to the SYNC® Symptom Chart before connecting the scan tool and beginning DTC-based diagnostics.
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to DIAGNOSTIC METHODS for information about these practices.
AUDIO FRONT CONTROL MODULE (ACM) DTC CHART (WITHOUT NAVIGATION)
| DTC | Description | Action |
|---|---|---|
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage out of Range | GO to PINPOINT TEST P . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit / Component Protection Time-Out | GO to PINPOINT TEST P . |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST C . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST C . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST C . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST C . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST C . |
| B1A05:02 | Speaker #5: General Signal Failure | GO to PINPOINT TEST E . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1D78:13 | Auxiliary Input: Circuit Open |
NOTE:
This DTC is only applicable for vehicles without SYNC®. For vehicles with SYNC®, disregard this DTC. GO to PINPOINT TEST Q . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AF . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST H . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AL . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AM . |
AUDIO FRONT CONTROL MODULE (ACM) DTC CHART (WITH NAVIGATION)
| DTC | Description | Action |
|---|---|---|
| B108E:63 | Display Circuit / Component Protection Time-Out - FDIM | CLEAR the DTCs. REPEAT the self-test. If DTC B108E:63 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST U . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST U . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage out of Range | GO to PINPOINT TEST P . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit / Component Protection Time-Out | GO to PINPOINT TEST P . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage out of Range | GO to PINPOINT TEST P . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit / Component Protection Time-Out | GO to PINPOINT TEST P . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B121C:44 | Hard Drive Data Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:44 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B . |
| B1D19:49 | Compact Disc Unit: Internal Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST L . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AF . |
| U2014:09 | Control Module Hardware: Component Failure | GO to PINPOINT TEST V . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST H . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U3000:45 | Control Module Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AL . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AM . |
ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST P . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit / Component Protection Time-Out | GO to PINPOINT TEST P . |
| B1252:04 | USB Port: System Internal Failure | GO to PINPOINT TEST Z . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to PINPOINT TEST Z . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST T . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST AH . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AK . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AF . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Global Positioning System Module (GPSM). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Front Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST X . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . REPEAT the self-test. |
| U3000:88 | Control Module: Bus Off |
NOTE:
Network communication/message DTCs may result from intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often set these DTCs. To avoid repeat network concerns, Inspect for damaged or corroded wiring at the APIM. Test the vehicle battery. Refer to Charging Systems in CHARGING SYSTEM -- MUSTANG
. Replacing a module to resolve a network DTC is unlikely to resolve the concern. The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AN . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AO . |
FRONT CONTROLS INTERFACE MODULE (FCIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AK . |
| U2013:63 | Switch Pack: Circuit / Component Protection Time-Out | GO to PINPOINT TEST I . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is still present, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . REPEAT the self-test. |
| U2014:42 (without navigation) | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AP . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AQ . |
FRONT DISPLAY INTERFACE MODULE (FDIM) DTC CHART - WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B1318 | Battery Voltage Low | GO to PINPOINT TEST AR . |
| B1342 | ECU is Faulted | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is still present, INSTALL a new Front Display Interface Module (FDIM). REFER to FRONT DISPLAY INTERFACE MODULE (FDIM) . REPEAT the self-test. |
| B2477 | Module Configuration Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT DISPLAY INTERFACE MODULE (FDIM) . |
| B2924 | Audio Button Stuck | CLEAR the DTCs. REPEAT the self-test. If DTC B2924 is still present, replace the FDIM. REFER to FRONT DISPLAY INTERFACE MODULE (FDIM) . REPEAT the self-test. |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST AB . |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | GO to PINPOINT TEST AC . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | GO to PINPOINT TEST AG . |
| U0184 | Lost Communication With Radio (ACM) | GO to PINPOINT TEST AK . |
| U0197 | Lost Communication With Telephone Control Module | GO to PINPOINT TEST AD . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION . |
| U2051 | One or More Calibration Files Missing/Corrupt | REFER to MODULE CONFIGURATION . |
GLOBAL POSITIONING SYSTEM MODULE (GPSM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Global Positioning System Module (GPSM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the GPSM or Instrument Panel Cluster (IPC). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . |
| U3000:09 | Control Module: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:09 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3000:41 | Control Module: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3000:42 | Control Module: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AS . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AT . |