LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Explorer Limited, 3.5 8, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 139 (Body System - Uni-Body, SUBFRAME & Mounting System) >> Removal And Installation >> Subframe - Front, 5.8L (4V) >> Installation

Subframe - Front, 5.8L (4V): Installation

WARNING: This page is about a different car, the 2013 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
  1. If installing a new subframe, transfer the steering rack and lower control arms to the new subframe. For additional information, refer to POWER STEERING and FRONT SUSPENSION .
  2. Position the subframe to the vehicle and loosely install the 4 front subframe nuts.
    G07489679
  3. NOTE: RH shown in illustration, LH similar.

    Loosely install the 4 rear subframe bolts.

    G07489677
  4. Use a suitable alignment tool with a 15 mm (0.59 in) OD shaft that is long enough to go through the subframe and body.
    • Align the subframe to the alignment marks made during removal.
  5. Tighten the 4 rear subframe bolts in a cross pattern to 115 Nm (85 lb-ft).
  6. Tighten the 4 front subframe nuts.
    • Tighten in a cross pattern to 115 Nm (85 lb-ft).
  7. Remove the Powertrain Lift Table or suitable device from the subframe.
  8. Connect the lower control arms to the wheel spindles.
    • Install new fasteners.
    • Tighten to 115 Nm (85 lb-ft).
  9. Connect the outer LH and RH tie-rod ends.
    • Install new fasteners.
    • Tighten to 80 Nm (59 lb-ft).
  10. Connect the steering shaft and install the steering shaft pinch bolt.
    • Tighten to 47 Nm (35 lb-ft).
      G07489676
  11. Connect the 2 EPAS electrical connectors and the pin-type retainer.
    G07487033
  12. NOTE: RH shown in illustration, LH similar.

    Install the crossmember brace and 4 bolts (2 shown in illustration).

    • Tighten to 65 Nm (48 lb-ft).
      G07489674
  13. NOTE: RH shown in illustration, LH similar.

    Tighten the 2 nuts for the crossmember brace to 65 Nm (48 lb-ft).

    G07489673
  14. Install the lower air deflector and the 9 bolts.
    • Tighten to 5 Nm (44 lb-in).
      G07489670
  15. Install the front tires and wheels. For additional information, refer to WHEELS AND TIRES .
  16. Using the Engine Support Bar, lower the engine in position.
  17. Remove the engine support bar.
  18. Remove the RH and LH engine lifting eyes.
  19. Install the RH and LH engine support insulator nuts.
    • Tighten to 63 Nm (46 lb-ft).
  20. Install the radiator sight shield and the 8 pin-type retainers.
    Fig 1: Locating Radiator Sight Shield Pin-Type Retainers
    G06403276Courtesy of FORD MOTOR CO.
  21. Install the ACL outlet pipe. For additional information, refer to INTAKE AIR DISTRIBUTION & FILTERING .
  22. Install the 2 steering column dash boot bearing nuts.
    • Tighten to 9 Nm (80 lb-in).
      Fig 2: Locating Steering Column Dash Boot Bearing Nuts
      G06394907Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals