LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Explorer Base, 3.5 8, AWD, 6F50 >> Repair and Diagnosis >> External Pages >> Different car >> Section 27 (Automatic Transmission - 6R140 (TORQSHIFT-R-6)) >> Diagnosis & Testing >> Pinpoint Tests >> Pinpoint Tests - Transmission Control Module (TCM) >> Pinpoint Test J: Output Shaft Speed (OSS) Sensor

Pinpoint Test J: Output Shaft Speed (OSS) Sensor

WARNING: This page is about a different car, the 2013 Ford F-550 Super Duty, 2013 Ford F-450 Super Duty, 2013 Ford F-350 Super Duty, and 2013 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: If the scan tool is unable to access the transmission PIDs, REFER to the INTRODUCTION - DIESEL MODELS or ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) .
NOTE: If DTCs P0706, P0707, P0708, P1702, P1705 and/or P1921 are set, diagnose those DTCs first.
NOTE: Read and record all DTCs.
  1. J1 DRIVE CYCLE TEST 
    • Enter the following diagnostic mode on the scan tool: OSS PID: OSS_SRC.
    • Monitor the Output Shaft Speed (OSS) sensor PID while road testing the vehicle. Drive the vehicle so the transmission upshifts and downshifts through all the gears.
    • Does the OSS sensor rpm increase and decrease with engine rpm and vehicle speed? 
  2. J2 CHECK THE OSS SIGNAL CIRCUIT FOR AN OPEN 
    • Disconnect: Transmission C1623.
    • Inspect the connector for damaged or pushed out terminals, corrosion, loose wires and missing or damaged seals.
    • Disconnect: Transmission Control Module (TCM) C1750.
    • Inspect the connector for damaged or pushed out terminals, corrosion, loose wires and missing or damaged seals.
    • Measure the resistance between the transmission vehicle harness C1623-17 circuit RET04 (YE/OG) and the TCM C1750-51.
      Fig 1: Measuring Resistance Between Transmission Vehicle Harness C1623-17 Circuit RET04 (YE/OG) And TCM C1750-51
      G07482756Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    • Yes  : GO to J3.
    • No  : REPAIR the OSS signal circuit for an open. CLEAR the DTCs. TEST the system for normal operation.
  3. J3 CHECK THE OSS SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    • Measure the resistance between the TCM C1750-51 circuit RET04 (YE/OG) and ground.
      Fig 2: Measuring Resistance Between TCM C1750-51 Circuit RET04 (YE/OG) And Ground
      G07482757Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10, 000 ohms? 
    • Yes  : GO to J4.
    • No  : REPAIR the OSS signal circuit for a short to ground. CLEAR the DTCs. TEST the system for normal operation.
  4. J4 CHECK THE OSS SIGNAL CIRCUIT FOR A SHORT TO POWER 
    • Ignition ON.
    • Check for voltage between the TCM C1750-51 circuit RET04 (YE/OG) and ground.
      Fig 3: Checking Voltage Between TCM C1750-51 Circuit RET04 (YE/OG) And Ground
      G07482757Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes  : REPAIR the OSS signal circuit for a short to voltage. CLEAR the DTCs. TEST the system for normal operation.
    • No  : GO to J5.
  5. J5 CHECK THE OSS SIGNAL CIRCUIT FOR POWER 
    • Ignition OFF.
    • Connect: PCM C1750.
    • Ignition ON.
    • Check for voltage between the transmission vehicle harness C1623-17 circuit RET04 (YE/OG) and ground.
      Fig 4: Checking Voltage Between Transmission Vehicle Harness C1623-17 Circuit RET04 (YE/OG) And Ground
      G07482744Courtesy of FORD MOTOR CO.
    • Is voltage greater than 4.6 volts? 
    • Yes  : GO to J6.
    • No  : REPLACE the TCM. PROGRAM the TCM with the latest calibration level. PERFORM the solenoid strategy download procedure. REFER to SOLENOID BODY STRATEGY . TEST the system for normal operation.
  6. J6 CHECK THE OSS INTERNAL HARNESS FOR AN OPEN 
    • Remove the transmission fluid pan.
    • Disconnect: 3-way OSS sensor connector.
    • Inspect the connector for damaged or pushed out terminals, corrosion, loose wires and missing or damaged seals.
    • Measure the resistance of the OSS sensor circuits between C1623 and the 3-way OSS sensor connector component side, using the following chart.
      Transmission OSS Sensor Circuit Terminal
      C1623-12 OSS Power 1
      C1623-17 OSS Signal 2
      C1623-10 OSS Ground 3
    • Is the resistance less than 5 ohms? 
    • Yes  : GO to J7.
    • No  : REPLACE the transmission internal harness. CLEAR the DTCs. TEST the system for normal operation.
  7. J7 CHECK THE OSS INTERNAL HARNESS FOR A SHORT TO GROUND 
    • Measure the resistance of the OSS sensor circuits between C1623 and ground using the following chart.
      Transmission OSS Sensor Circuit Ground
      C1623-12 OSS Power Ground
      C1623-17 OSS Signal Ground
      C1623-10 OSS Ground Ground
    • Is the resistance greater than 10, 000 ohms? 
    • Yes  : REPLACE the OSS sensor.
    • No  : REPLACE the transmission internal harness. CLEAR the DTCs. TEST the system for normal operation. If DTCs P0720, P0721 and/or P0722 return, REPLACE the TCM. PROGRAM the TCM with the latest calibration level. PERFORM the solenoid strategy download procedure. REFER to SOLENOID BODY STRATEGY . TEST the system for normal operation.
scientia non olet · About LEMON Manuals