LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Explorer Base, 3.5 8, AWD, 6F50 >> Repair and Diagnosis >> External Pages >> Different car >> Section 226 (Automatic Transmission - 6F35) >> Diagnosis And Testing >> Automatic Transmission >> Diagnostic Routines >> Pinpoint Test C: SSC >> Pinpoint Test C: Shift Solenoid C

Pinpoint Test C: Shift Solenoid C

WARNING: This page is about a different car, the 2013 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
  1. C1 RETRIEVE AND RECORD ALL DTCS 
    • Using the diagnostic scan tool, retrieve all DTCs.

    Are DTCs P0760, P0763, P0764, P0979 and/or P0980 present? 

    1. Yes  : For DTCs P0760, P0763, and P0764, GO to C2  .

      For DTC P0979, GO to  C5.

      For DTC P0980, GO to  C7.

    2. No  : GO to SYMPTOM CHART .
  2. C2 CHECK THE SSC CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Disconnect: Transmission Vehicle Harness C1520A  .
    • Disconnect: TCM C1750  .
    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.
    • Measure the resistance  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      C1520A-4  CET07 (GY/OG) C1750-6  CET07 (GY/OG)
      Fig 1: Identifying Transmission Vehicle Harness (C1520A) And TCM (C1750) Connector Terminals
      G08411582Courtesy of FORD MOTOR CO.

    Is the resistance less than 3 ohms? 

    1. Yes  : GO to C3  .
    2. No  : REPAIR the circuit.
  3. C3 CHECK THE SSC FOR AN OPEN 
    • Measure the component side resistance  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      4 - 5 -
      Fig 2: Identifying SSC Connector Terminals
      G08411583Courtesy of FORD MOTOR CO.

    Is the resistance between 4.0 and 7.2 ohms? 

    1. Yes  : INSTALL a new TCM  . REFER to TRANSMISSION CONTROL MODULE (TCM) . PROGRAM the TCM  with the latest calibration level. PERFORM the Solenoid Body Strategy Download procedure. REFER to SOLENOID BODY STRATEGY DOWNLOAD .
    2. No  : GO to C4  .
  4. C4 CHECK THE SSC RESISTANCE 
    • Remove the solenoid body leadframe, refer to SOLENOID BODY LEADFRAME . Inspect for metal shavings on the exposed metal contacts or other components and clean the solenoid and solenoid body leadframe terminals.
    • Measure SSC resistance  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      A - B -
      G08031026Courtesy of FORD MOTOR CO.

    Is the resistance between 4.0 and 7.2 ohms? 

    1. Yes  : INSTALL a new solenoid body leadframe. REFER to SOLENOID BODY LEADFRAME .
    2. No  : INSTALL a new SSC  . REFER to SOLENOIDS .
  5. C5 CHECK THE SSC CIRCUIT FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Disconnect: Transmission Vehicle Harness C1520A  .
    • Disconnect: TCM C1750  .
    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.
    • Measure the resistance  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      C1520A-4  CET07 (GY/OG) - Ground
      Fig 3: Identifying Transmission Vehicle Harness (C1520A) Connector Terminals
      G09087748Courtesy of FORD MOTOR CO.

    Is the resistance greater than 10, 000 ohms? 

    1. Yes  : GO to C6  .
    2. No  : REPAIR the circuit.
  6. C6 CHECK THE SSC FOR A SHORT TO GROUND 
    • Remove the solenoid body leadframe, refer to SOLENOID BODY LEADFRAME . Inspect for metal shavings on the exposed metal contacts or other components and clean the solenoid and solenoid body leadframe terminals.
    • Measure SSC resistance  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      A - - Ground
      G08031026Courtesy of FORD MOTOR CO.

    Is the resistance less than 3 ohms? 

    1. Yes  : INSTALL a new SSC  . REFER to SOLENOIDS .
    2. No  : INSTALL a new solenoid body leadframe. REFER to SOLENOID BODY LEADFRAME .
  7. C7 CHECK THE SSC CIRCUIT FOR A SHORT TO VOLTAGE 
    • Ignition OFF.
    • Disconnect: Transmission Vehicle Harness C1520A  .
    • Disconnect: TCM C1750  .
    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.
    • Ignition ON.
    • Measure the voltage  between.
      Positive Lead Negative Lead
      Pin Circuit Pin Circuit
      C1520A-4  CET07 (GY/OG) - Ground
      Fig 4: Identifying Transmission Vehicle Harness (C1520A) Connector Terminals
      G09087750Courtesy of FORD MOTOR CO.

    Is any voltage present? 

    1. Yes  : REPAIR the circuit.
    2. No  : INSTALL a new TCM  . REFER to TRANSMISSION CONTROL MODULE (TCM) . PROGRAM the TCM  with the latest calibration level. PERFORM the Solenoid Body Strategy Download procedure. REFER to SOLENOID BODY STRATEGY DOWNLOAD .
scientia non olet · About LEMON Manuals