Pinpoint Test

NOTE: When taking measurements at DCSM harness connectors, do not insert the electrical probes into the female connector pins. Inserting the probes into connector pins can cause intermittent or open electrical connections after reassembly resulting in DTCs and system failure. Touching the tip of these connector pins is recommended instead.

CHECK THE TED CIRCUITS FOR AN OPEN

WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

Ignition OFF.
Disconnect: Driver Seat Side Air Bag C3051.
Disconnect: Passenger Seat Side Air Bag C339.
Disconnect: DCSM C3265A.
Disconnect: Driver Cushion TED C3035.
Disconnect: Driver Backrest TED C3034.

Measure:

DCSM			Driver Cushion TED

C3265A			C3035
Pin	Circuit	Measurement / Action	Pin	Circuit
G	CHS02 (YE/BU)		1	CHS02 (YE/BU)
H	RHS02 (BU/OG)		3	RHS02 (BU/OG)

DCSM			Driver Backrest TED

C3265A			C3034
Pin	Circuit	Measurement / Action	Pin	Circuit
J	CHS01 (GY/VT)		1	CHS01 (GY/VT)
K	RHS01 (WH/VT)		3	RHS01 (WH/VT)

Are the resistances less than 3 ohms?

Yes: GO to 2 .
No: REPAIR the affected circuit. GO to 5 .

CHECK THE TED CIRCUITS FOR A SHORT TO VOLTAGE

Ignition ON.

Measure:

DCSM			Ground

C3265A			Ground
Pin	Circuit	Measurement / Action	Pin	Circuit
G	CHS02 (YE/BU)		-	Ground
H	RHS02 (BU/OG)		-	Ground
J	CHS01 (GY/VT)		-	Ground
K	RHS01 (WH/VT)		-	Ground

Is any voltage present on any circuits?

Yes: REPAIR the affected circuit. GO to 5 .
No: GO to 3 .

CHECK THE RESISTANCE OF THE TEDs

Ignition OFF.

Measure:

Driver Backrest TED			Driver Backrest TED

C3034 Component Side			C3034 Component Side
Pin	Circuit	Measurement / Action	Pin	Circuit
1	-		3	-

Driver Cushion TED			Driver Cushion TED

C3035 Component Side			C3035 Component Side
Pin	Circuit	Measurement / Action	Pin	Circuit
1	-		3	-

Are the resistances between 0.9 and 10 ohms?

Yes: GO to 4 .
No: If the resistance of the backrest TED was not between 0.9 and 10 ohms, INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device (TED) . GO to 5.
If the resistance of the cushion TED was not between 0.9 and 10 ohms, INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device (TED) . GO to 5.

CHECK FOR CORRECT DCSM OPERATION
1. Ignition OFF.
2. Disconnect and inspect all DCSM connectors.
3. Repair:
  - corrosion (install new connector or terminals - clean module pins)
  - damaged or bent pins - install new terminals/pins as necessary
  - pushed-out pins - install new pins as necessary
4. Reconnect the DCSM connectors. Make sure they seat and latch correctly.
5. Connect: Driver Seat Backrest TED C3034.
6. Connect: Driver Seat Cushion TED C3035.
7. Operate the system and determine if the concern is still present.
Is the concern still present?
1. Yes: CHECK OASIS for any applicable TSBs . If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) . GO to 5 .
2. No: The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. GO to 5 .
CHECK FOR SRS DTCs
1. WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
  
  Ignition OFF.
2. Connect: Driver Seat Side Air Bag C3051.
3. Connect: Passenger Seat Side Air Bag C339.
4. Connect: DCSM C3265A (if previously disconnected).
5. Connect: Driver Seat Backrest TED C3034.
6. Connect: Driver Seat Cushion TED C3035.
7. Ignition ON.
8. Using a scan tool, clear the RCM DTCs .
9. Cycle the ignition OFF then ON.
10. Using a scan tool, perform RCM self-test.
Are any RCM DTCs retrieved during self-test?
1. Yes: REFER to DTC CHART: RESTRAINT CONTROL MODULE (RCM) for pinpoint test direction.
2. No: The repair is complete. RETURN the vehicle to the customer.