Pinpoint Test

1. Ignition ON.
2. Verify there is an observable symptom present.

Is an observable symptom present? 

• Yes: GO to 2  .
• No: The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

1. Ignition ON.
2. Using a scan tool, perform a network test.

Does the BCM pass the network test? 

• Yes: GO to 3  .
• No: REFER to Diagnostic Routine I: The Body Control Module (BCM) Does Not Respond To The Scan Tool .

1. Using a scan tool, clear the DTCs  .
2. Repeat the SOD-R  or the SOD-L  self-test.

Is DTC U0140:00 still present? 

• Yes: GO to 4  .
• No: The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

1. Ignition ON.
2. Using a scan tool, clear continuous DTCs  from all modules.
3. Ignition OFF.
4. Ignition ON.
5. Wait at least 10 seconds.
6. Retrieve all continuous DTCs  from all modules.

Is DTC U0140:00 set in any other module? 

• Yes: GO to 5  .
• No: If DTC U0140:00 only sets in SOD-L  , GO to  6. If DTC U0140:00 only sets in SOD-R  , GO to  7.

1. Disconnect and inspect the BCM connectors.
2. Repair:
   • corrosion (install new connector or terminals - clean module pins)
   • damaged pins - install new terminals/pins
   • pushed-out pins - install new pins as necessary
3. Reconnect the BCM connectors. Make sure they seat and latch correctly.

Is the concern still present? 

• Yes: CHECK OASIS  for any applicable TSBs  . If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs  address this concern, INSTALL a new BCM:

  REFER to BODY CONTROL MODULE (BCM) - WITH INTELLIGENT ACCESS (IA) , or

  REFER to BODY CONTROL MODULE (BCM) - WITHOUT INTELLIGENT ACCESS (IA) .

• No: The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

1. Disconnect and inspect the SOD-L  connector.
2. Repair:
   • corrosion (install new connector or terminals - clean module pins)
   • damaged pins - install new terminals/pins
   • pushed-out pins - install new pins as necessary
3. Connect the SOD-L  connector and make sure it seats correctly.
4. Operate the system and verify the concern is still present.

Is the concern still present? 

• Yes: CHECK OASIS  for any applicable TSBs  . If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs  address this concern, INSTALL a new SOD-L  . REFER to Side Obstacle Detection (SOD) Module .
• No: The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

1. Disconnect and inspect the SOD-R  connector.
2. Repair:
   • corrosion (install new connector or terminals - clean module pins)
   • damaged pins - install new terminals/pins
   • pushed-out pins - install new pins as necessary
3. Reconnect the SOD-R  connector. Make sure it seats and latches correctly.
4. Operate the system and determine if the concern is still present.

Is the concern still present? 

• Yes: CHECK OASIS  for any applicable TSBs  . If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs  address this concern, INSTALL a new SOD-R  . REFER to Side Obstacle Detection (SOD) Module .
• No: The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.