LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2011 >> Taurus SHO >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> Fuel Charging System - Turbocharger >> Removal And Installation >> Turbocharger - RH >> Removal

Turbocharger - RH: Removal

NOTE: Whenever turbocharger air intake system components are removed, always cover open ports to protect from debris. It is important that no foreign material enter the system. The turbocharger compressor vanes are susceptible to damage from even small particles. All components should be inspected and cleaned, if necessary, prior to installation or reassembly.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING Article.
    2. NOTE: Use a steering wheel holding device (such as Hunter® 28-75-1 or equivalent).
    Fig 1: Holding Steering Wheel
    G06063988Courtesy of FORD
  2. Using a suitable holding device, hold the steering wheel in the straight-ahead position.
  3. Remove the 4 retainers and the underbody shield.
    Fig 2: Locating Underbody Shield And Retainers
    G06261404Courtesy of FORD
  4. Drain the cooling system. For additional information, refer to ENGINE COOLING SYSTEM Article.
  5. Remove the RH catalytic converter. For additional information, refer to EXHAUST SYSTEM Article.
  6. Remove the front subframe. For additional information, refer to BODY SYSTEM - UNI-BODY, SUBFRAME & MOUNTING SYSTEM Article.
  7. Remove the RH turbocharger oil supply tube secondary latch.
    Fig 3: Locating RH Turbocharger Oil Supply Tube Secondary Latch
    G06261405Courtesy of FORD
  8. Using a Spring Lock Coupling Disconnect Tool, remove the RH turbocharger oil supply tube from the quick connect fitting.
    • Inspect and if necessary, replace the quick connect fitting.
      Fig 4: Removing RH Turbocharger Oil Supply Tube From Quick Connect Fitting
      G06261406Courtesy of FORD
  9. Remove the lower RH exhaust manifold heat shield bolt.
    Fig 5: Locating Lower RH Exhaust Manifold Heat Shield Bolt
    G06261443Courtesy of FORD
  10. Loosen the clamp and remove the RH turbocharger intake pipe from the RH turbocharger.
    Fig 6: Locating RH Turbocharger Intake Pipe Clamp
    G06261408Courtesy of FORD
  11. Disconnect the turbocharger wastegate regulating valve hose from the RH turbocharger assembly.
    Fig 7: Locating Turbocharger Wastegate Regulating Valve Hose
    G06282049Courtesy of FORD
  12. Remove the 3 bolts and the RH turbocharger lower bracket.
    Fig 8: Locating RH Turbocharger Lower Bracket And Bolts
    G06261410Courtesy of FORD
  13. Remove the 2 bolts and the RH turbocharger oil return tube from the turbocharger.
    • Remove and discard the gasket.
      Fig 9: Locating RH Turbocharger Oil Return Tube Bolts
      G06261411Courtesy of FORD
  14. Remove the RH turbocharger oil return tube from the cylinder block.
    • Discard the 2 O-ring seals.
      Fig 10: Locating RH Turbocharger Oil Return Tube
      G06261412Courtesy of FORD
  15. Remove the 2 coolant tube banjo bolts and the RH turbocharger coolant tubes.
    • Discard the sealing washers.
      Fig 11: Locating Coolant Tube Banjo Bolts And RH Turbocharger Coolant Tubes
      G06261413Courtesy of FORD
  16. Detach the 2 vacuum hose retainers from the strut tower brace.
  17. Remove the 4 nuts and the strut tower brace.
  18. Disconnect the LH turbocharger bypass valve electrical connector and the turbocharger bypass valve hose.
    Fig 12: Locating LH Turbocharger Bypass Valve Electrical Connector And Turbocharger Bypass Valve Hose Clamp
    G06261414Courtesy of FORD
  19. Remove the turbocharger wastegate regulating valve hose from the RH Charge Air Cooler (CAC) tube.
    Fig 13: Locating Turbocharger Wastegate Regulating Valve Hose
    G06261415Courtesy of FORD
  20. Disconnect the RH turbocharger bypass valve electrical connector.
    Fig 14: Locating RH Turbocharger Bypass Valve Electrical Connector
    G06261416Courtesy of FORD
  21. Disconnect the RH turbocharger bypass valve hose.
    Fig 15: Locating RH Turbocharger Bypass Valve Hose
    G06261417Courtesy of FORD
  22. Remove the RH CAC tube nut from the intake manifold.
    Fig 16: Locating RH CAC Tube Nut
    G06261431Courtesy of FORD
  23. Loosen the clamp and remove the RH CAC tube.
    Fig 17: Locating RH CAC Tube Clamp
    G06261430Courtesy of FORD
  24. Loosen the clamp and remove the RH CAC tube from the RH turbocharger.
    Fig 18: Locating RH CAC Tube Clamp Of RH Turbocharger
    G06261420Courtesy of FORD
  25. Remove the 4 bolts and the 2 upper RH exhaust manifold heat shields.
    Fig 19: Locating Upper RH Exhaust Manifold Heat Shields And Bolts
    G06261421Courtesy of FORD
  26. Remove the 2 bolts and the RH engine lifting eye.
  27. Remove the 3 RH exhaust manifold-to-turbocharger bolts.
    • Discard the gasket.
      Fig 20: Locating RH Exhaust Manifold-To-Turbocharger Bolts
      G06261422Courtesy of FORD
  28. Remove the upper RH turbocharger-to-cylinder block bracket bolt and the RH turbocharger assembly.
    Fig 21: Locating Upper RH Turbocharger-To-Cylinder Block Bracket Bolt
    G06261426Courtesy of FORD
  29. Remove the RH turbocharger oil supply tube banjo bolt.
    • Discard the sealing washer and oil supply tube filter.
scientia non olet · About LEMON Manuals