LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2011 >> Taurus Limited, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Wiper/Washer Systems >> Wiper System & Washer System >> Diagnosis And Testing >> Wipers and Washers >> Pinpoint Tests >> Pinpoint Test G: The Headlamps Do Not Illuminate When the Wipers are On >> Pinpoint Test G: The Headlamps Do Not Illuminate When The Wipers Are On

Pinpoint Test G: The Headlamps Do Not Illuminate When The Wipers Are On

NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
  1. G1 CHECK THE WIPER MOTOR ON INPUT VOLTAGE TO THE WINDSHIELD WIPER MOTOR 
    • Disconnect: Wiper Motor C125.
    • Ignition ON.
    • Turn the headlamp control switch to the AUTOLAMP position.
    • Measure the voltage between wiper motor C125-2, circuit CRW01 (WH), harness side and ground.
      Fig 1: Measuring Voltage Between Wiper Motor C125-2, Circuit CRW01 (WH), Harness Side And Ground
      G06071243Courtesy of FORD MOTOR CO.
    • Is the voltage greater than 10 volts? 
    • Yes  : GO to  G3.
    • No  : GO to G2.
  2. G2 CHECK CIRCUIT CRW01 (WH) FOR AN OPEN OR SHORT TO GROUND 
    • Ignition OFF.
    • Disconnect: SJB C2280F.
    • Measure the resistance between SJB C2280F-8, circuit CRW01 (WH), harness side and wiper motor C125-2, circuit CRW01 (WH); and between SJB C2280F-8, circuit CRW01 (WH), harness side and ground.
      Fig 2: Checking Circuit CRW01 (WH) For Open Or Short To Ground
      G06071244Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the SJB and wiper motor and greater than 10, 000 ohms between the SJB and ground? 
    • Yes  : GO to  G4.
    • No  : REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
  3. G3 CHECK THE WIPER ACTIVATED HEADLAMPS OPERATION 
      NOTE: When performing the following test, the light sensor must have enough light to have the headlamps deactivated.
      Fig 3: Connecting Fused Jumper Wire Between Wiper Motor C125-2 Circuit CRW01 (WH), Harness Side And Ground
      G06393220Courtesy of FORD MOTOR CO.
    • Connect a fused jumper wire between wiper motor C125-2 circuit CRW01 (WH), harness side and ground.
    • Do the headlamps turn on within 10 seconds? 
    • Yes  : INSTALL a new wiper motor. REFER to WIPER MOTOR  . CLEAR the DTCs. REPEAT the self-test.
    • No  : GO to G4.
  4. G4 CHECK FOR CORRECT MODULE OPERATION 
    • Disconnect all the SJB connectors.
    • Check for:
      • corrosion.
      • pushed-out pins.
    • Connect all the SJB connectors and make sure they are seated correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    • Yes  : INSTALL a new SJB. REFER to MULTIFUNCTION ELECTRONIC MODULE Article. CLEAR the DTCs. REPEAT the self-test.
    • No  : The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
scientia non olet · About LEMON Manuals