Brake Shoes &/Or Pads: Remove & Replace
Includes: Clean, lube and/or replace Brake Hardware as necessary. Adjust Brakes (where applicable). Includes: Repack Wheel Bearings (where applicable). DOES NOT include refinishing.| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|---|---|---|---|
| All,Both Axles | 1.8 | B | ||
| Front,Both Sides | 1.0 | B | ||
| Rear,Both Sides | 1.0 | B | ||
| Combination Procedure: BRAKE HOSE: Replace: Includes: Bleed Brake System. | ||||
| Each Additional | 0.2 | B | ||
| One | 0.3 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 2.9 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Seperable | 3.1 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 1.7 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Seperable | 1.8 | B | ||
| Combination Procedure: CALIPER: Overhaul: | ||||
| One | Includes: Bleed Brakes. | 0.7 | B | |
| Combination Procedure: CALIPER: Replace: | ||||
| One | Includes: Bleed Brakes. | 0.3 | B | |
| Combination Procedure: DISC ROTOR: Burnish Brake Rotors While Driving Vehicle: | ||||
| 0.5 | B | |||
| Combination Procedure: DISC ROTOR: Remove and Install for Refinishing: NOTE: This operation does not apply to drive axles. If on vehicle refinishing is not possible use appropriate repair operation. | ||||
| Front,Each | 0.5 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 2.9 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Seperable | 2.3 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 1.7 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Seperable | 1.4 | B | ||
| Combination Procedure: DISC ROTOR: Replace: | ||||
| Front,Each | Includes: Repack Wheel Bearings. | 0.5 | B | |
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 2.9 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Seperable | 2.3 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 1.7 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Seperable | 1.4 | B | ||
| Combination Procedure: OIL SEAL WEAR SLEEVE: Replace: | ||||
| Each | 0.2 | B | ||
| Combination Procedure: PARKING BRAKE SHOE & LINING: Replace: | ||||
| Rear,Both Sides,Full Floating Axle | 2.8 | B | ||
| Rear,One Side,Full Floating Axle | 1.7 | B | ||
| Trans Mounted,Assembly,One Piece Driveline | 2.2 | B | ||
| Trans Mounted,Assembly,Two Piece Driveline | 2.4 | B | ||
| Combination Procedure: WHEEL BEARING: Repack: | ||||
| Front,Both Sides | 0.8 | B | ||
| Rear,Both Sides | 2.1 | B | ||
| Rear,One Side | 1.3 | B | ||
| Combination Procedure: WHEEL BEARING: Replace: | ||||
| Front,One Side | 0.5 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 2.9 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Seperable | 3.1 | B | ||
| Rear,Both Sides,Full Floating Axle,Outboard Mounted Rotor | 3.3 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 1.7 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Seperable | 1.8 | B | ||
| Rear,One Side,Full Floating Axle,Outboard Mounted Rotor | 1.7 | B | ||
| Combination Procedure: WHEEL HUB: Replace: | ||||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 2.9 | B | ||
| Rear,Both Sides,Full Floating Axle,Inboard Mounted Rotor,Seperable | 3.1 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Non Seperable | 1.7 | B | ||
| Rear,One Side,Full Floating Axle,Inboard Mounted Rotor,Seperable | 1.8 | B | ||