PINPOINT TEST C: DTCs C1145, C1155, C1165 AND C1175

NOTE: Use the Flex Probe Kit for all test connections to prevent damage to the wiring terminals. Do not use standard multi-meter probes.

C1 CHECK FOR FAULT REPEATABILITY
- Connect the scan tool.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - All CMDTCs.
- Drive the vehicle at least 16 km/h (10 mph).
- Retrieve and document continuous DTCs.
- Is DTC C1145, C1155, C1165 or C1175 retrieved?
  - Yes : If the Active Wheel Speed Sensor Tester is available, GO to C2. If the Active Wheel Speed Sensor Tester is not available, GO to C4.
  - No : INSPECT the wheel speed sensors, wheel speed sensor wiring and wheel speed sensor tone rings. REPAIR or INSTALL new as necessary. If any other DTCs are retrieved, GO to the ABS MODULE DTC CHART .
C2 CHECK THE ABS MODULE OUTPUT USING THE ACTIVE WHEEL SPEED SENSOR TESTER
- Ignition OFF.
- Disconnect: Suspect Wheel Speed Sensor.
- Connect the Active Wheel Speed Sensor Tester to the wheel speed sensor connectors.
- Ignition ON.
- Select the correct system polarity on the Active Wheel Speed Sensor Tester and turn power switch to the ON position.
- Is the module output LED illuminated?
  - Yes : GO to C3.
  - No : GO to C6.
C3 CHECK THE WHEEL SPEED SENSOR OUTPUT WITH THE ACTIVE WHEEL SPEED SENSOR TESTER
- Raise the suspect wheel until it can spin freely. Refer to JACKING & LIFTING article.
- While monitoring the Active Wheel Speed Sensor Tester, slowly spin the suspect wheel.
- Do the sensor output LEDs illuminate and flash and is the current overload LED not illuminated?
  - Yes : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
  - No : If the current level LED is not illuminated and the sensor output LEDs do not illuminate or if the current level LED is illuminated red, INSTALL a new wheel speed sensor. For the front wheel speed sensor, REFER to WHEEL SPEED SENSOR - FRONT . For the rear wheel speed sensor, REFER to WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.
  If the current level LED is not illuminated and the sensor output LEDs illuminate green, but do not flash, INSPECT the wheel speed sensor tone ring and INSTALL new if necessary. If the tone ring is OK, INSTALL a new wheel speed sensor. For the front wheel speed sensor, REFER to WHEEL SPEED SENSOR - FRONT . For the rear wheel speed sensor, REFER to WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.
C4 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO VOLTAGE
NOTE: Both circuits must be checked for each DTC.
- Ignition OFF.
- Disconnect: ABS Module C155.
- Disconnect: Suspect Wheel Speed Sensor.
- Ignition ON.
- For DTC C1145 , measure the voltage between ground and:
  - ABS module C155-34, circuit VCA05 (GY/VT), harness side.
  - ABS module C155-33, circuit RCA19 (VT), harness side.
  Fig 1: Measuring Voltage Between Ground With ABS Module C155-34 And C155-33
  Courtesy of FORD MOTOR CO.
- For DTC C1155 , measure the voltage between ground and:
  - ABS module C155-45, circuit VCA03 (VT/WH), harness side.
  - ABS module C155-46, circuit RCA17 (YE), harness side.
  Fig 2: Measuring Voltage Between Ground With ABS Module C155-45 And C155-46
  Courtesy of FORD MOTOR CO.
- For DTC C1165 , measure the voltage between ground and:
  - ABS module C155-43, circuit VCA06 (WH/OG), harness side.
  - ABS module C155-42, circuit RCA20 (BN), harness side.
  Fig 3: Measuring Voltage Between Ground With ABS Module C155-43 And C155-42
  Courtesy of FORD MOTOR CO.
- For DTC C1175 , measure the voltage between ground and:
  - ABS module C155-36, circuit VCA04 (BU/OG), harness side.
  - ABS module C155-37, circuit RCA18 (BN/GN), harness side.
  Fig 4: Measuring Voltage Between Ground With ABS Module C155-36 And C155-37
  Courtesy of FORD MOTOR CO.
- Is any voltage present?
  - Yes : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  - No : GO to C5.
C5 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO GROUND
NOTE: Both circuits must be checked for each DTC.
- Ignition OFF.
- For DTC C1145 , measure the resistance between ground and:
  - ABS module C155-34, circuit VCA05 (GY/VT), harness side.
  - ABS module C155-33, circuit RCA19 (VT), harness side.
  Fig 5: Measuring Resistance Between Ground With ABS Module C155-34 And C155-33
  Courtesy of FORD MOTOR CO.
- For DTC C1155 , measure the resistance between ground and:
  - ABS module C155-45, circuit VCA03 (VT/WH), harness side.
  - ABS module C155-46, circuit RCA17 (YE), harness side.
  Fig 6: Measuring Resistance Between Ground With ABS Module C155-45 And C155-46
  Courtesy of FORD MOTOR CO.
- For DTC C1165 , measure the resistance between ground and:
  - ABS module C155-43, circuit VCA06 (WH/OG), harness side.
  - ABS module C155-42, circuit RCA20 (BN), harness side.
  Fig 7: Measuring Resistance Between Ground With ABS Module C155-43 And C155-42
  Courtesy of FORD MOTOR CO.
- For DTC C1175 , measure the resistance between ground and:
  - ABS module C155-36, circuit VCA04 (BU/OG), harness side.
  - ABS module C155-37, circuit RCA18 (BN/GN), harness side.
  Fig 8: Measuring Resistance Between Ground With ABS Module C155-36 And C155-37
  Courtesy of FORD MOTOR CO.
- Are the resistances greater than 10, 000 ohms?
  - Yes : GO to C6.
  - No : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.

C6 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR AN OPEN

NOTE: Both circuits must be checked for each DTC.

Ignition OFF.
Disconnect: ABS Module C155.

Disconnect: Suspect Wheel Speed Sensor.

Measure the resistance between ABS module C155, harness side and the suspect wheel speed sensor connector, harness side as indicated in the following chart:

ABS Module	Circuit	Wheel Speed Sensor
DTC C1145 - Wheel Speed Sensor RF Input Circuit Failure
C155-34	VCA05 (GY/VT)	C160-2
C155-33	RCA19 (VT)	C160-1
DTC C1155 - Wheel Speed Sensor LF Input Circuit Failure
C155-45	VCA03 (VT/WH)	C150-2
C155-46	RCA17 (YE)	C150-1
DTC C1165 - Wheel Speed Sensor RR Input Circuit Failure
C155-43	VCA06 (WH/OG)	C426-2
C155-42	RCA20 (BN)	C426-1
DTC C1175 - Wheel Speed Sensor LR Input Circuit Failure
C155-36	VCA04 (BU/OG)	C440-2
C155-37	RCA18 (BN/GN)	C440-1

Are the resistances less than 5 ohms?
- Yes : GO to C7.
- No : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the ABS self-test.

C7 CHECK FOR SHORTED WHEEL SPEED SENSOR CIRCUITS
- For DTC C1145 , measure the resistance between RF wheel speed sensor C160-2, circuit VCA05 (GY/VT), harness side and RF wheel speed sensor C160-1, circuit RCA19 (VT), harness side.
  
  Fig 9: Measuring Resistance Between RF Wheel Speed Sensor C160-2, Circuit VCA05 (GY/VT) And C160-1, Circuit RCA19 (VT)
  Courtesy of FORD MOTOR CO.
- For DTC C1155 , measure the resistance between LF wheel speed sensor C150-2, circuit VCA03 (VT/WH), harness side and LF wheel speed sensor C150-1, circuit RCA17 (YE), harness side.
  
  Fig 10: Measuring Resistance Between LF Wheel Speed Sensor C150-2, Circuit VCA03 (VT/WH) And C150-1, Circuit RCA17 (YE)
  Courtesy of FORD MOTOR CO.
- For DTC C1165 , measure the resistance between RR wheel speed sensor C426-2, circuit VCA06 (WH/OG), harness side and RR wheel speed sensor C426-1, circuit RCA20 (BN), harness side.
  
  Fig 11: Measuring Resistance Between RR Wheel Speed Sensor C426-2, Circuit VCA06 (WH/OG) And C426-1, Circuit RCA20 (BN)
  Courtesy of FORD MOTOR CO.
- For DTC C1175 , measure the resistance between LR wheel speed sensor C440-2, circuit VCA04 (BU/OG), harness side and LR wheel speed sensor C440-1, circuit RCA18 (BN/GN), harness side.
  
  Fig 12: Measuring Resistance Between LR Wheel Speed Sensor C440-2, Circuit VCA04 (BU/OG) And C440-1, Circuit RCA18 (BN/GN)
  Courtesy of FORD MOTOR CO.
- Are the resistances greater than 10, 000 ohms?
  - Yes : GO to C8.
  - No : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
C8 CHECK THE ABS MODULE OUTPUT
- Connect: ABS Module C155.
- Ignition ON.
- For DTC C1145 , measure the voltage between RF wheel speed sensor C160-2, circuit VCA05 (GY/VT), harness side and RF wheel speed sensor C160-1, circuit RCA19 (VT), harness side.
- For DTC C1155 , measure the voltage between LF wheel speed sensor C150-2, circuit VCA03 (VT/WH), harness side and LF wheel speed sensor C150-1, circuit RCA17 (YE), harness side.
- For DTC C1165 , measure the voltage between RR wheel speed sensor C426-2, circuit VCA06 (WH/OG), harness side and RR wheel speed sensor C426-1, circuit RCA20 (BN), harness side.
- For DTC C1175 , measure the voltage between LR wheel speed sensor C440-2, circuit VCA04 (BU/OG), harness side and LR wheel speed sensor C440-1, circuit RCA18 (BN/GN), harness side.
  
  Fig 13: Measuring Voltage Between LR Wheel Speed Sensor C440-2, Circuit VCA04 (BU/OG) And C440-1, Circuit RCA18 (BN/GN)
  Courtesy of FORD MOTOR CO.
- Are the voltages greater than 10 volts?
  - Yes : INSTALL a new wheel speed sensor. REFER to WHEEL SPEED SENSOR - FRONT or WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.
  - No : GO to C9.
C9 CHECK FOR CORRECT ABS MODULE OPERATION
- Ignition OFF.
- Disconnect: ABS Module C155.
- Check the connector for:
  - corrosion.
  - pushed-out pins.
  - spread terminals.
- Connect: ABS Module C155.
- Make sure the connector seats correctly, then operate the system and verify the concern is still present.
- Is the concern still present?
  - Yes : INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTCs. REPEAT the self-test.
  - No : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.