DTC Chart: Instrument Panel Cluster (IPC)
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to DIAGNOSTIC METHODS for information regarding Ford-specific diagnostic practices.
DTC CHART-INSTRUMENT PANEL CLUSTER (IPC)
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor A Circuit: Circuit Short to Ground | REFER to Diagnostic Routine B . |
| P0460:13 | Fuel Level Sensor A Circuit: Circuit Open | REFER to Diagnostic Routine B . |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure | REFER to Diagnostic Routine B . |
| P1346:11 | Fuel Level Sensor B Circuit: Circuit Short to Ground | REFER to Diagnostic Routine B . |
| P1346:13 | Fuel Level Sensor B Circuit: Circuit Open | REFER to Diagnostic Routine B . |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) and diagnose all Restraints Control Module (RCM) Diagnostic Trouble Codes (DTCs). REFER to DTC CHART: RESTRAINT CONTROL MODULE (RCM) . |
| P1706:62 | High Vehicle Speed Observed in Park: Signal Compare Failure | REFER to Diagnostic Routine CK . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | REFER to Diagnostic Routine AR . |
| U0101:00 | Lost Communication With TCM: No Sub-Type Information | REFER to Diagnostic Routine AS . |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub-Type Information | REFER to Diagnostic Routine AT . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub-Type Information | REFER to Diagnostic Routine AU . |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub-Type Information | REFER to Diagnostic Routine BX . |
| U0138:00 | Lost Communication with All Terrain Control Module: No Sub-Type Information | REFER to Diagnostic Routine BY . |
| U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | REFER to Diagnostic Routine AV . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub-Type Information | REFER to Diagnostic Routine AW . |
| U0154:00 | Lost Communication With Occupant Classification Sensor (OCS): No Sub-Type Information | REFER to Diagnostic Routine AX . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub-Type Information | REFER to Diagnostic Routine AY . |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub-Type Information | REFER to Diagnostic Routine AZ . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub-Type Information | REFER to Diagnostic Routine BB . |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub-Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid network data for the cruise control, odometer count, fuel alcohol percent, tachometer, temperature and All-Wheel Drive (AWD) lock torque from the Powertrain Control Module (PCM). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Powertrain Control Module (PCM) and other modules on the network. REFER to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) . |
| U0401:81 | Invalid Data Received From ECM/PCM A: Invalid Serial Data Received | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid network data for temperature and vehicle speed from the Powertrain Control Module (PCM). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Powertrain Control Module (PCM) and other modules on the network. REFER to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) . |
| U0405:56 | Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid network data for adaptive cruise control from the Powertrain Control Module (PCM). CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0415:56 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid data for stability-traction control configuration or trailer sway configuration from the Anti-Lock Brake System (ABS) module. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub-Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid data for brake fluid level or tire pressure from the Body Control Module (BCM). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Body Control Module (BCM). REFER to DTC CHART: BODY CONTROL MODULE (BCM) . |
| U0422:56 | Invalid Data Received From Body Control Module: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives Body Control Module (BCM) data for the autolamp function and Instrument Panel Cluster (IPC) is not configured for autolamps. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives unknown outside air temperature data from the Heating, Ventilation, and Air Conditioning (HVAC) module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Powertrain Control Module (PCM) and the Heating, Ventilation, and Air Conditioning (HVAC) module. REFER to DTC CHART: HEATING VENTILATION AIR CONDITIONING (HVAC) MODULE - ELECTRONIC MANUAL TEMPERATURE CONTROL (EMTC) and REFER to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) . |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid outside air temperature data from the Heating, Ventilation, and Air Conditioning (HVAC) module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Powertrain Control Module (PCM) and the Heating, Ventilation, and Air Conditioning (HVAC) module. REFER to DTC CHART: HEATING VENTILATION AIR CONDITIONING (HVAC) MODULE - ELECTRONIC MANUAL TEMPERATURE CONTROL (EMTC) and REFER to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) . |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | REFER to Diagnostic Routine BC . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid data for the Belt-Minder® from the Restraints Control Module (RCM) module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Restraints Control Module (RCM). REFER to DTC CHART: RESTRAINT CONTROL MODULE (RCM) . |
| U045A:00 | Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid data for parking aid and active park assist from the Parking Aid Module (PAM). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Parking Aid Module (PAM). REFER to DTC CHART: PARKING AID MODULE (PAM) . |
| U045A:56 | Invalid Data Received From Parking Assist Control Module "A": Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) configuration for parking aid does not match the data received.
NOTE:
The Instrument Panel Cluster (IPC) does not display the parking aid settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U045A:81 | Invalid Data Received From Parking Assist Control Module "A": Invalid Serial Data Received | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid rear parking aid data from the Parking Aid Module (PAM). The Instrument Panel Cluster (IPC) is not configured for parking aid.
NOTE:
The Instrument Panel Cluster (IPC) does not display the check mark in the parking aid settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U046B:86 | Invalid Data Received From Global Positioning System Module: Signal Invalid | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid compass data from the Accessory Protocol Interface Module (APIM).
NOTE:
The compass displays dashes (- -) or is blank depending on the display mode. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Accessory Protocol Interface Module (APIM). REFER to DTC CHART: ACCESSORY PROTOCOL INTERFACE MODULE (APIM) - PREMIUM PLUS or REFER to DTC CHART: ACCESSORY PROTOCOL INTERFACE MODULE (APIM) - SONY SOUND . |
| U0531:56 | Invalid Data Received From Rear Gate Module: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives rear liftgate data from the Liftgate/Trunk Module (LTM) when the Instrument Panel Cluster (IPC) is not configured for rear liftgate or if the Instrument Panel Cluster (IPC) does not receive expected liftgate data when it is configured for rear liftgate.
NOTE:
The Instrument Panel Cluster (IPC) does not display the power liftgate settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives blind spot or side obstacle detection data when the Instrument Panel Cluster (IPC) is not configured for Blind Spot Information System (BLIS) or if the Instrument Panel Cluster (IPC) does not receive blind spot or side obstacle detection data when it is configured for Blind Spot Information System (BLIS).
NOTE:
The Instrument Panel Cluster (IPC) does not display the Blind Spot Information System (BLIS) or Cross Traffic Alert (CTA) settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated | This Diagnostic Trouble Code (DTC) sets in the Instrument Panel Cluster (IPC) when the side obstacle detection data remains unchanged from the Side Obstacle Detection Control Module - Left (SOD-L) for more than 1.6 seconds.
NOTE:
The Instrument Panel Cluster (IPC) displays a fault warning message and does not display the check mark in the Blind Spot Information System (BLIS) settings in the message center. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Side Obstacle Detection Control Module - Left (SODL). REFER to DTC CHART: SIDE OBSTACLE DETECTION MODULE - LEFT (SOD-L) AND SIDE OBSTACLE DETECTION MODULE - RIGHT (SOD-R) . |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives blind spot or side obstacle detection data when the Instrument Panel Cluster (IPC) is not configured for Blind Spot Information System (BLIS) or if the Instrument Panel Cluster (IPC) does not receive blind spot or side obstacle detection data when it is configured for Blind Spot Information System (BLIS).
NOTE:
The Instrument Panel Cluster (IPC) does not display the Blind Spot Information System (BLIS) or Cross Traffic Alert (CTA) settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | This Diagnostic Trouble Code (DTC) sets in the Instrument Panel Cluster (IPC) when the side obstacle detection data remains unchanged from the Side Obstacle Detection Control Module - Right (SOD-R) for more than 1.6 seconds.
NOTE:
The Instrument Panel Cluster (IPC) displays a fault warning message and does not display the check mark in the Blind Spot Information System (BLIS) settings in the message center. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Side Obstacle Detection Control Module - Right (SOD-R). REFER to DTC CHART: SIDE OBSTACLE DETECTION MODULE - LEFT (SOD-L) AND SIDE OBSTACLE DETECTION MODULE - RIGHT (SOD-R) . |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when the Instrument Panel Cluster (IPC) receives invalid clock data from the Accessory Protocol Interface Module (APIM) for more than 5 seconds.
NOTE:
The Instrument Panel Cluster (IPC) displays all dashes (- -) for the time of day. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the Accessory Protocol Interface Module (APIM). REFER to DTC CHART: ACCESSORY PROTOCOL INTERFACE MODULE (APIM) - PREMIUM PLUS or REFER to DTC CHART: ACCESSORY PROTOCOL INTERFACE MODULE (APIM) - SONY SOUND . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:41 is retrieved again, INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| U3000:43 | Control Module: Special Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:43 is retrieved again, INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:44 is retrieved again, INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| U3000:45 | Control Module: Program Memory Failure | CARRY OUT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:45 is retrieved again, INSTALL a new Instrument Panel Cluster (IPC). REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to Diagnostic Routine BD . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to Diagnostic Routine BE . |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | Diagnostic Trouble Code (DTC) U300A:64 sets on-demand and in continuous memory when the Instrument Panel Cluster (IPC) detects a messaged START input for 15 seconds or more. Once the fault condition is detected, the Instrument Panel Cluster (IPC) operates with limited functionality for 15 seconds then returns to full functionality. REFER to Diagnostic Routine D or REFER to Diagnostic Routine E to diagnose the ignition start circuit to the Body Control Module (BCM). |